manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

Flexible static memory controller (FSMC)

RM0365

275/1080

DocID025202 Rev 7

When this functionality is required, it can be ensured by programming the MEMHOLD value 
to meet the t

WB

 timing. However any CPU read access to the NAND Flash memory has a 

hold delay of (M 2) HCLK cycles and CPU write access has a hold delay of 
(MEMHOLD) HCLK cycles inserted between the rising edge of the NWE signal and the next 
access.

To cope with this timing constraint, the attribute memory space can be used by 
programming its timing register with an ATTHOLD value that meets the t

WB

 timing, and by 

keeping the MEMHOLD value at its minimum value. The CPU must then use the common 
memory space for all NAND Flash read and write accesses, except when writing the last 
address byte to the NAND Flash device, where the CPU must write to the attribute memory 
space.

14.6.6 

Computation of the error correction code (ECC) 
in NAND Flash memory

The FMC PC Card controller includes two error correction code computation hardware 
blocks, one per memory bank. They reduce the host CPU workload when processing the 
ECC by software.

These two ECC blocks are identical and associated with Bank 2 and Bank 3. As a 
consequence, no hardware ECC computation is available for memories connected to Bank 
4.

The ECC algorithm implemented in the FMC can perform 1-bit error correction and 2-bit 
error detection per 256, 512, 1 024, 2 048, 4 096 or 8 192 bytes read or written from/to the 
NAND Flash memory. It is based on the Hamming coding algorithm and consists in 
calculating the row and column parity.

The ECC modules monitor the NAND Flash data bus and read/write signals (NCE and 
NWE) each time the NAND Flash memory bank is active.

The ECC operates as follows:

•

When accessing NAND Flash memory bank 2 or bank 3, the data present on the 
D[15:0] bus is latched and used for ECC computation. 

•

When accessing any other address in NAND Flash memory, the ECC logic is idle, and 
does not perform any operation. As a result, write operations to define commands or 
addresses to the NAND Flash memory are not taken into account for ECC 
computation.

Once the desired number of bytes has been read/written from/to the NAND Flash memory 
by the host CPU, the FMC_ECCR2/3 registers must be read to retrieve the computed value. 
Once read, they should be cleared by resetting the ECCEN bit to ‘0’. To compute a new data 
block, the ECCEN bit must be set to one in the FMC_PCR2/3 registers.

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

D-Link DES-1210-08P Manual preview
DES-1210-08P
Бренд: D-Link Страницы: 15
National Instruments NI 9213 Getting Started preview
NI 9213
Бренд: National Instruments Страницы: 11
Salto Node Installation Manual preview
Node
Бренд: Salto Страницы: 2
Accuphase AD-60 Instruction Manual preview
AD-60
Бренд: Accuphase Страницы: 2
ADTRAN ATLAS 550 Manual preview
ATLAS 550
Бренд: ADTRAN Страницы: 2
Acrosser Technology AMB-VDX3H1 Series Quick Start Manual preview
AMB-VDX3H1 Series
Бренд: Acrosser Technology Страницы: 4
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Бренд: National Instruments Страницы: 15
iCEBOX Z86K15 Manual preview
Z86K15
Бренд: iCEBOX Страницы: 57
Bridgeworks Oresund EFC102200 User Manual preview
Oresund EFC102200
Бренд: Bridgeworks Страницы: 84
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Бренд: NKE Страницы: 15
Aaeon SBC-657B Manual preview
SBC-657B
Бренд: Aaeon Страницы: 61
Freescale Semiconductor MPC8349EA MDS Getting Started Manual preview
MPC8349EA MDS
Бренд: Freescale Semiconductor Страницы: 8
Swann NVRx-7300 series Quick Start Manual preview
NVRx-7300 series
Бренд: Swann Страницы: 9
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Бренд: Ubiquiti Страницы: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Бренд: CG Страницы: 112
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Бренд: Lattice Semiconductor Страницы: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Бренд: Paradyne Страницы: 19
Gearlinx NR4400 Series User'S Quick Start Manual preview
NR4400 Series
Бренд: Gearlinx Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды