Still FXV 14 N Скачать руководство пользователя страница 53

Страница: 53 / 152

Driver's compartment settings

Adjusting the seat

The seat is equipped with an operator pres-

ence detector.
The operator must adjust his weight by incre-

ments of 10 kg to trigger this detection.
Proceed as follows:

–

Sit on the seat

–

Turn the adjustment wheel (1) until the de-

sired weight is reached

–

Put the truck into service

The seat's operator presence detector cannot

be activated if the weight setting is too high or

too low.
This operation also enables you to adjust the

hardness of the seat.

Adjusting the floor

The floor is fitted with a pressure-based height

adjustment system.
To adjust the floor height, proceed as follows:

–

Sit on the seat.

–

Press the floor unlocking button (2) and

hold it down for the duration of the opera-

tion.

–

Exert pressure on the floor (3) by pushing it

with your legs to obtain a good driving posi-

tion.

–

Release the button.

NOTE

Adjusting the floor is not possible when the

truck is in cold store. The cylinder for adjust-

ment does not work at low temperatures.



Use

Driver's compartment settings

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Still FXV 14 N, Оригинальное руководство пользователя, Страница: 53 / 152

Результаты поиска

Содержание FXV 14 N

Отзывы: