Still FXV 14 N Скачать руководство пользователя страница 50

Страница: 50 / 152

Stepping on/off the truck

WARNING

Risk of falling, tripping or slipping when stepping

on/off the truck.
Use the handle (1) and the seat (2) to help when

stepping on/off the truck.

–

Hold the handle (1) with one hand

–

Hold onto the seat (2) with the other hand

–

Step onto the platform (3), paying close at-

tention to your step

CAUTION

Risk of injury or impact from the edges of the truck.
The chassis is narrow. Be careful not to hit yourself

on the truck when stepping onto it.

CAUTION

Risk of damaging the equipment

–

Never pull on the steering wheel or control unit

when climbing onto the truck.

Excessive force on the steering wheel or the control

unit can damage it and cause a malfunction.

DANGER

Risk of injury
To avoid accidental start-up, do not use the control

module as a handle.
Use the handle and the seat.



Use

Stepping on/off the truck

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды

Still FXV 14 N, Оригинальное руководство пользователя

Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды