Still FXV 14 N Скачать руководство пользователя страница 120

Страница: 120 / 152

Recommended lubricants

CAUTION

Damage to equipment if non-recommended lubri-

cants are used.
Only use recommended lubricants. Only the lubri-

cants listed below are approved by the manufacturer.

Do not mix lubricants. If in doubt, please contact the

After-Sales Service Centre.

Hydraulic oil

Recommended oil for standard use:
ISO-L-HM 46 as per ISO 6743-4 or ISO

VG46-HLP as per DIN 51524-2
Recommended oil for heavy-duty use:
ISO-L-HM 68 as per ISO 6743-4 or ISO

VG68-HLP as per DIN 51524-2
Recommended oil for the cold store version:
ISO-L-HM 32 as per ISO 6743-4 or ISO

VG32-HLP as per DIN 51524-2

Transmission oil

Recommended oil:

SAE 85W 90 API GL4

Aerosol can for chains

Standard chain spray

Grease for pinion gear and steering ring

CAUTION

Follow the maintenance and safety guidelines.

Multi-purpose grease

Lithium soap grease with EP agents and

MoS 2KPF 2N - 20 complying with the stand-

ard DIN 51825.

ENVIRONMENT NOTE

Used oil must be stored safely until it is dis-

posed of in accordance with environmental

regulations. No one should have access to the

used oil. Do not dispose of used oil in drains

or allow it to penetrate soil.

Maintenance

Recommended lubricants

110

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Похожие инструкции для FXV 14 N

Бренды по названию

Популярные бренды

Still FXV 14 N, Оригинальное руководство пользователя

Результаты поиска

Содержание FXV 14 N

Отзывы:

Похожие инструкции для FXV 14 N

Бренды по названию

Популярные бренды