Still FS-X33 Скачать руководство пользователя страница 87

Страница: 87 / 94

Special equipment

Cold store cab

Thermostat for the heating system in

the cold store cab

The required temperature of the cab heating

can be selected via the thermostat. To do this,

set the adjustment wheel to the adjustment

mark (1) for the required heating level.

Cold store cab fuses

Fuses

The control current fuses for the cab are

installed next to the door hinge behind the

sheet metal cover. The following fuses are

used in the standard cold store cab:
• 30 A; heating system next to the driver’s

seat

• 30 A; heating system in the door
• 15 A; door and right-hand side screen

heating

• 15 A; Front and left-hand side screen

heating

• 3 A; working spotlight (optional)
• 3 A; radio voltage transformer (optional)

51328042507 [EN]

Содержание FS-X33































































































Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды

Still FS-X33, Оригинальное руководство пользователя

Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды