Still FS-X33 Скачать руководство пользователя страница 71

Страница: 71 / 94

Maintenance

Lubrication plan for cold store application

every 2,000 hours or every 12 months
• Change the hydraulic oil

Lubrication plan for cold store

application

For lubrication tasks in accordance with the

lubrication plan, we recommend the following

low-temperature lubricants:

Area of application

Lubricant

Filling bearings with grease

Lubricating sliding faces

Almetyn SF2, ID no. 8052 346 (aluminium

complex soaps with parafﬁn-based base oil)

Lubricating moving parts, e.g. levers, push-rod

switches of limit switches, turning handles etc. Kompranol N74, ID no. 8050 077

Hydraulics

Fuchs Renolin MR310 hydraulic oil, ID no.

8036 239 (Factory ﬁll not mixable with other

hydraulic oils)

Gearbox

SAE 75W-90 gearbox oil, semi-synthetic, ID

no. 8036 929, oil quality must conform at least

to API GL5 or MIL-L-2105-B.

For protecting the ﬁne pitch thread during

cylinder assembly

Rivolta G. W. F. spray, ID no. 8050 078,

thread-loosening, anti-wear and lubricating

solution

Chain spray

High performance chain spray, ID no. 8052

453

Maintenance schedule

This maintenance schedule is valid for normal

loading during single-shift operation. For

heavy-duty and/or multi-shift operation, the

intervals must be reduced accordingly. Please

observe the information in the section entitled

Area of application.

Maintenance every six months or every

1000 hrs

Traction drives
• Check the gearbox for noise and leakages.
• Initial gearbox oil change.
• Check the tightness of the screw connection

to the drive units (note the torque).

51328042507 [EN]

Содержание FS-X33































































































Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды

Still FS-X33, Оригинальное руководство пользователя

Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды