manualshive.com logo in svg

Still EXD 18, Оригинальное руководство пользователя

Поделиться
Скачать
Still EXD 18 Скачать руководство пользователя страница 59

FleetManager™ option: Colour code for the LEDs 

The LEDs can have different statuses and dif-

ferent colours. Below is the list of the most

common messages and their meanings.

Malfunction

Cause

Solution

LED status

Signal transmitter  

 

LED 1

LED 2

Lit continuously

Red colour

Off

A long acoustic

signal sounds

Reading device

variant: no valid

access authorisa-

tion

Generate a valid

access authorisa-

tion using the in-

terface

Keypad variant:

no valid access

authorisation for

the PIN code en-

tered

Keypad variant:

PIN code entered

incorrect or not

confirmed using

the Enter key

Re-enter the PIN

code

Lit continuously

Red colour

Flashes once

Green colour

A long acoustic

signal sounds

The operator has

been granted ac-

cess authorisa-

tion. But the peri-

od of validity has

expired.

Use the interface

to enter a new pe-

riod of validity

The date of the

truck is incorrect

Update the date

of the truck

Flashes quickly

Yellow colour

Lit continuously

Green colour

 

Memory is 80%

full

Clear the memory

Flashes quickly

Red colour

Flashes quickly

Red colour

A long acoustic

signal sounds

upon activation

There are several

possible causes:

- Reading device

or keypad not ac-

cessible

- GPRS module

not accessible

- Built-in re-

chargeable bat-

tery flat

- Memory full

Contact the After-

Sales Service

Centre

Use

4

Operating the FleetManager™ option

 49

1160 801 15 51 EN - 02/2021  -  11

Содержание EXD 18



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды