Still EXD 18 Скачать руководство пользователя страница 45

Страница: 45 / 146

Checks and actions prior to commissioning

Start-up

–

Connect the battery connector, if necessa-

ry.

–

Keep the tiller in the vertical position.

–

Place the drive direction selector in the neu-

tral position (in the middle).

–

Insert the ignition key (1) and turn it to the

desired position or enter the 5-figure code

then validate using the # key on the digi-

code keyboard (default code = 00000).

NOTE

With the digicode option, when the key is

turned to the 0 position the truck is in tortoise

mode. The truck will function even if the key is

removed.

Selecting the driving mode

NOTE

The switch key can rotate to two different posi-

tions. These two positions choose the operat-

ing mode.

"Tortoise" position (2): gentle acceleration and

deceleration; maximum speed: 4 km/h.
"Hare" position (3): strong acceleration and

deceleration; maximum speed: 6 km/h.

–

Check the battery charge on the combined

indicator (4) and replace or charge the bat-

tery if necessary.

–

Turn the ignition key (1) to the "hare" posi-

tion (3) for normal driving mode.

NOTE

Perform a visual inspection of the truck before

starting.



Use

Checks and actions prior to commissioning

1160 801 15 51 EN - 02/2021 - 11

Содержание EXD 18



















































































































































Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды

Still EXD 18, Оригинальное руководство пользователя

Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды