Still ECU-SF-20 Скачать руководство пользователя страница 63

Страница: 63 / 92

Maintenance

Maintenance as required

Fuse replacement

2154

1F1

2F1

1F2

3F1

• Turn off the truck and perform the prelimi-

nary maintenance operations.

DANGER

For models with an optional cooling fan (SERVICE

KIT), the fans may move even when the key is in the

OFF position.
Risk of cutting!

CAUTION

Before replacing the fuse, eliminate the cause that

led to its blowing. The blown fuse must only be

replaced with a fuse of the same amperage. Do not

tamper with the truck’s electrical system.

– Raise the battery cover as indicated in the

relative section.

Fuse values

Power Fuses

– Unscrew the nut, change the fuse and

tighten the nut again.

Fuse values
• 1F1 = 150 A traction motor safety fuse
• 2F1 = 80 A pump motor safety fuse

Service fuses

– Remove the cover and replace the blown

fuse, then replace the cover.

Fuse values
• V2 = 8 A step plate sensor protection diode
• V1 = 8 A power supply polarity protection

diode

• 1F2 = 5 A electromagnetic brake safety fuse
• F1 = 10 A safety fuse
• 3F1 = 30 A steering motor safety fuse

Optional fuses

Fuse values
9F1 = 2 A fan safety fuse
9F3 = 2 A cold store safety fuse

45378043402 [EN]

Содержание ECU-SF-20





























































































Результаты поиска

Содержание ECU-SF-20

Отзывы:

Still ECU-SF-20, Оригинальное руководство пользователя, Страница: 63 / 92

Результаты поиска

Содержание ECU-SF-20

Отзывы: