Still ECU-SF-20 Скачать руководство пользователя страница 57

Страница: 57 / 92

Use and Operation

Battery Recharging

CAUTION

The battery is recharged with the forklift off.

DANGER

The battery must be charged in rooms that comply

with the speciﬁc regulations on the subject. Refer

to the battery and battery charger manual for the

charging procedures, level checks etc., checking

the type of battery (gel, lead etc.) and the voltage

and current delivered. Excessive currents can

damage batteries and cause dangerous situations.

As far as the safety precautions are concerned,

follow the instructions given in the battery manual

and those included in "Safety regulations "of this

manual.

• Access the upper part of the battery as

described in the "Internal accessibility"

paragraph.

• Remove the battery caps (if indicated in the

battery maintenance booklet).

• Turn on the external battery charger.
• Connect plug the battery charger in to begin

charging.

• After the battery charging operation is

completed, turn off the battery charger.

• Unplug the battery charger.
• Replace the battery caps (if removed

previously).

• Plug the battery in again.
• Lower the battery compartment cover.

NOTE

Refer to the battery charger manual for more

information.

45378043402 [EN]

Содержание ECU-SF-20





























































































Результаты поиска

Содержание ECU-SF-20

Отзывы:

Still ECU-SF-20, Оригинальное руководство пользователя, Страница: 57 / 92

Результаты поиска

Содержание ECU-SF-20

Отзывы: