Still ECU-SF-20 Скачать руководство пользователя страница 53

Страница: 53 / 92

Use and Operation

Load Placement

Forklift Use in Cold-Storage Rooms.

A truck speciﬁcally equipped for cold-storage

rooms must be used when working at temper-

atures below +5°C.
Forklifts equipped for working in cold climates

and cold-storage rooms may be used at a

minimum temperature of -5°C for continuous

service in cold-storage rooms and at -32°C

for non-continuous service in cold-storage

rooms.

CAUTION

The forklift must always be turned off and parked

outside the cold area/cold-storage room.

CAUTION

If the truck has been working in environments at

temperatures below -5°C and it is taken outside the

cold-storage room, let it stand either for a sufﬁcien-

tly long time to allow evaporation of any condensa-

tion (at least 30 minutes) or a sufﬁciently short time

to prevent the formation of any condensation (less

than 10 minutes).
Avoid the formation of ice on the forklift.

CAUTION

NEVER drive the truck into the cold-storage room

when condensation has formed on it

Using the truck with extension leads

DANGER

The truck may only be used with extension leads

ﬁtted with a ﬁlter approved by the manufacturer,

with a maximum length of 20 m.

Load Placement

Taking up load

DANGER

Before lifting the load, make sure that its dimensi-

ons and centre of gravity fall within the forklift spe-

ciﬁcations, as indicated in the TECHNICAL DATA

chapter

DANGER

The loads must be arranged so that they cannot slip

or overturn and fall to the ground.

DANGER

Make sure that nobody is standing in the forklift’s

area of operation.

45378043402 [EN]

Содержание ECU-SF-20





























































































Результаты поиска

Содержание ECU-SF-20

Отзывы:

Still ECU-SF-20, Оригинальное руководство пользователя, Страница: 53 / 92

Результаты поиска

Содержание ECU-SF-20

Отзывы: