Still ECU-SF-20 Скачать руководство пользователя страница 51

Страница: 51 / 92

Use and Operation

Use of the Truck

Using the truck on inclines, loading

bridges and lifts.

Driving on inclines

When driving the truck up or down inclines,

you must not exceed the values for inclines

indicated in the chapter "Technical data".
The driver must check that the ground is clean

with a good grip.

WARNING

Drive at a reduced speed on descending slopes.

DANGER

Risk of tipping!
When driving up inclines, do not turn or travel

diagonally.

Using the truck on an incline

– When driving on an incline without a load,

the forks must face the bottom of the incline.

WARNING

When driving on an incline with a load, you must

keep the load pointing towards the top of the incline.

DANGER

Risk of accident
Keep the truck at a safe distance from the edges of

ramps, tailboards etc.

CAUTION

In certain cases, it is permitted to drive with the

forks pointing towards the top of the incline even if

the truck is not loaded.
In these cases, drive with the utmost care and avoid

turning until all the wheels are on a ﬂat surface.

45378043402 [EN]

Содержание ECU-SF-20





























































































Результаты поиска

Содержание ECU-SF-20

Отзывы:

Still ECU-SF-20, Оригинальное руководство пользователя, Страница: 51 / 92

Результаты поиска

Содержание ECU-SF-20

Отзывы: