Still ECU-SF-20 Скачать руководство пользователя страница 49

Страница: 49 / 92

Use and Operation

Use of the Truck

Reverse drive

Reverse of direction without load on forks

• To reverse direction when travelling without

a load on the fork arms, turn the traction

control throttle in the opposite direction of

travel. The truck will stop with energetic but

gradual braking and will start to move again

in the opposite direction.

Reverse of direction with load on forks

• To reverse direction with a load on the fork

arms, release the traction control throttle

and wait for the truck to come to a stop.

• Reverse direction using the traction control

throttle.

DANGER

Brake by adapting deceleration to the type of load

you are carrying so that you don’t lose the load

itself.

Truck braking/stopping

The truck can be braked by:
• Releasing the tiller.
• Reversing the direction of travel using the

traction control throttle.

NOTE

Rotating the traction control throttle in the

opposite direction activates counter-current

braking.

WARNING

When the truck is stationary, the parking brake

takes over through the electromagnetic brake.

45378043402 [EN]

Содержание ECU-SF-20





























































































Результаты поиска

Содержание ECU-SF-20

Отзывы:

Still ECU-SF-20, Оригинальное руководство пользователя, Страница: 49 / 92

Результаты поиска

Содержание ECU-SF-20

Отзывы: