Still ECU-SF-20 Скачать руководство пользователя страница 23

Страница: 23 / 92

Safety

Safety tests

Regelmäßige Prüfung

(FEM 4.004)

nach nationalen Vorschriften
basierend auf den EG-Richtlinien:
95/63/EG, 99/92/EG, 2001/45/EG

Die Prüfplakette ersetzt nicht das Prüfprotokoll

Nächste Prüfung

56344391019

Mitglied der:
Fédération
Européene
de la Manutention

STILL GmbH Hamburg

0000_003-001_V3

Regular safety inspection of the truck

Safety inspection based on time and

extraordinary incidents

The operating company must ensure that

the truck is checked at least once a year, or

following noteworthy incidents.
As part of this inspection, a complete check

of the technical condition of the truck must be

performed with regard to accident safety.

In addition, the truck must be thoroughly

checked for damage that could potentially

have been caused by improper use. A test

log must be created. The results from the

inspection must be retained until a further two

inspections have been carried out.
The inspection date is indicated by an adhe-

sive label on the truck.
– Arrange for the service centre to perform

periodic safety inspections on the truck.

– Observe guidelines for checks carried out

on the truck in accordance with FEM 4.004.

The operator is responsible for ensuring any

defects are remedied without delay.
– Contact your service centre.

NOTE

Observe the national regulations for your

country!

45378043402 [EN]

Содержание ECU-SF-20





























































































Результаты поиска

Содержание ECU-SF-20

Отзывы:

Still ECU-SF-20, Оригинальное руководство пользователя, Страница: 23 / 92

Результаты поиска

Содержание ECU-SF-20

Отзывы: