Stihl TS 500i Скачать руководство пользователя страница 105

Страница: 105 / 118

104

TS 500i

11.6.3 Tank vent Removal and

installation

– Remove the air filter,

11.1

Pry out the tank vent (1)

Always fit a new tank vent.

Installation

– Use STIHL press fluid to simplify

assembly,

Examine the bushing (1), pry it
out and replace if necessary

Install the bushing (1) so that the
rubber lip encloses the hole
completely

Align the new tank vent (2) so
that the connector (arrow) points
downwards

Push the new tank vent (2) as far
as possible into the bushing

1307RA207 TG

1307RA208 TG

– Reassemble remaining parts in

reverse order

11.7

Injection pump

11.7.1 Manual fuel pump

After the injection pump has been
removed, replace the fuel hose unit.
First, check if only the manual fuel
pump needs to be replaced.

The manual fuel pump can be
repaired with the fuel hoses still
attached.

– Remove the shroud,

6.4

– Remove the control unit,

7.3

Pull the injection pump (1) from
the guide (arrow)

1307RA209 TG

Remove screws (1)
– The two other screws (2)
guarantee the function preset at
the factory and must therefore
not be loosened or unscrewed

Remove flange (3), cap (4) and
compression spring (5)

– Examine the individual parts,

replace if necessary

Installation

Insert the compression spring (1)
into the mount (arrows)

1307RA210 TG

5 4

1307RA211 TG

Содержание TS 500i























































































































Результаты поиска

Содержание TS 500i

Отзывы:

Похожие инструкции для TS 500i

Бренды по названию

Популярные бренды

Stihl TS 500i, Руководство по обслуживанию

Результаты поиска

Содержание TS 500i

Отзывы:

Похожие инструкции для TS 500i

Бренды по названию

Популярные бренды