Stihl SR 430 Скачать руководство пользователя страница 44

Страница: 44 / 111

SR 430, SR 450

Fit the new pawls (1) in the
bores (arrows) and lubricate the
pegs on the pawls with grease,

Position the spring clip (1) so that
its loops engage the pegs on the
pawls. The rounded part of the
spring clip (short arrow) must
engage the starter post’s groove.

Push the straight part of the
spring clip over the starter post
until it snaps into the groove.

0002RA109 TG

0002RA110 TG

The spring clip's guide loops must
be in line with the pawls (arrows).

– Check operation.

– Pull the starter rope. The rope

rotor turns and the pegs move in
the direction of the spring loop
– the pawls swing outwards.

– Reassemble all other parts in the

reverse sequence.

6.4

Rope Rotor

Relieving tension of rewind
spring

– Remove the starter cover,

6.2

Pull out the starter rope (1)
about 5 cm and hold the rope
rotor (2) steady.

0002RA111 TG

0002RA112 TG

– Take three full turns of the rope

off the rope rotor.

– Pull out the rope with the starter

grip and slowly release the rope
rotor.

– Remove the starter rope or

remaining rope from the rotor.

The system will not be under
tension if the starter rope is broken
or the rewind spring is worn.

– Remove the spring clip and

pawls,

6.3

Remove the washer (1).

Rewind spring must be relaxed.

– Carefully remove the rope

rotor (2).
– The rewind spring may pop out
and unwind.

– Remove the starter rope,

6.5

– Coat starter post and bore in rope

rotor with STIHL special
lubricant,

0002RA113 TG

Содержание SR 430
















































































































Результаты поиска

Содержание SR 430

Отзывы:

Бренды по названию

Популярные бренды

Stihl SR 430, Руководство пользователя

Результаты поиска

Содержание SR 430

Отзывы:

Бренды по названию

Популярные бренды