Stihl MSE 250 C Скачать руководство пользователя

Страница: 31 / 36

29 Maintenance and Repairs

Users of this machine may only carry out the

maintenance and service work described in this

user manual. All other repairs must be carried

out by a servicing dealer.
STIHL recommends that you have servicing and

repair work carried out exclusively by an author‐

ized STIHL servicing dealer. STIHL dealers are

regularly given the opportunity to attend training

courses and are supplied with the necessary

technical information.
When repairing the machine, only use replace‐

ment parts which have been approved by STIHL

for this power tool or are technically identical.

Only use high-quality replacement parts in order

to avoid the risk of accidents and damage to the

machine.
STIHL recommends the use of original STIHL

replacement parts.
Original STIHL parts can be identified by the

STIHL part number, the

{

logo and the

STIHL parts symbol

(the symbol may appear

alone on small parts).

30 Disposal

Observe all country-specific waste disposal rules

and regulations.

000BA073 KN

STIHL products must not be thrown in the gar‐

bage can. Take the product, accessories and

packaging to an approved disposal site for envi‐

ronment-friendly recycling.
Contact your STIHL servicing dealer for the lat‐

est information on waste disposal.

31 EC Declaration of Con‐

formity

ANDREAS STIHL AG & Co. KG

Badstr. 115

D-71336 Waiblingen

Germany
declares under our sole responsibility that
Designation:

Electric saw

Make:

STIHL

Series:

MSE 250 C

Serial identification number: 1210
conforms to the relevant provisions of Directives

2011/65/EU, 2006/42/EC, 2014/30/EU and

2000/14/EC and has been developed and manu‐

factured in compliance with the following stand‐

ards in the versions valid on the date of produc‐

tion:
EN 60745‑1, EN 60745‑2‑13, EN 55014‑1,

EN 55014‑2, EN 61000‑3‑2, EN 61000‑3‑3
The measured and the guaranteed sound power

level have been determined in accordance with

Directive 2000/14/EC, Annex V, and standard

ISO 22868.
Measured sound power level
MSE 250 C:

106 dB(A)

Guaranteed sound power level
MSE 250 C:

108 dB(A)

The EC type examination pursuant to Directive

2006/42/EC Art. 12.3(b) was carried out by
VDE Prüf- und Zertifizierungsinstitut (NB 0366)

Merianstrasse 28

D-63069 Offenbach
Certification No.:

MSE 250 C:

40037736

Technical documents deposited at:
ANDREAS STIHL AG & Co. KG

Produktzulassung
The year of construction, the country of manufac‐

ture and the machine number are shown on the

machine.
Done at Waiblingen, 03.02.2020
ANDREAS STIHL AG & Co. KG
pp

Dr. Jürgen Hoffmann
Head of Product Data, Regulations and Licens‐

ing

29 Maintenance and Repairs

English

0458-764-0121-B

Содержание MSE 250 C





































Результаты поиска

Содержание MSE 250 C

Отзывы:

Похожие инструкции для MSE 250 C

Бренды по названию

Популярные бренды

Stihl MSE 250 C, Инструкция по эксплуатации

Результаты поиска

Содержание MSE 250 C

Отзывы:

Похожие инструкции для MSE 250 C

Бренды по названию

Популярные бренды