Stihl MSE 250 C Скачать руководство пользователя

Страница: 24 / 36

The drive link tangs will otherwise scrape along

the bottom of the groove – the cutters and tie

straps will not ride on the bar rails.

20 Motor Cooling

9913BA013 KN

► Use a dry brush or similar tool to clean the

cooling slots at regular intervals – see "Mainte‐

nance Chart".

21 Storing the Machine

For periods of 3 months or longer

► Disconnect the plug from the wall outlet.

► Remove the saw chain and guide bar, clean

them and spray with corrosion inhibiting oil.

► Thoroughly clean the machine, especially the

cooling air inlets.

► If you use a biological chain and bar lubricant,

e.g. STIHL BioPlus, completely fill the chain oil

tank.

► Store the machine in a dry and secure location

– out of the reach of children and other unau‐

thorized persons.

22 Checking and Replacing

the Chain Sprocket

► Disconnect the plug from the wall outlet.

► Remove the chain sprocket cover, chain and

guide bar.

22.1

Replacing the Chain Sprocket

9913BA015 KN

1 Chain sprocket (8 teeth)

–

replace after using two saw chains or sooner

–

if the wear marks (a) on the sprocket are

deeper than 0.5 mm – the life of the chain

would otherwise be reduced. Use reference

gauge (special accessory) to check the depth

of the wear marks.

It is best to use two saw chains in rotation with

one sprocket.
STIHL recommends the use of original STIHL

sprockets to ensure correct operation of the

chain brake.

9931BA016 KN

► Ease the E-clip (1) off the shaft.

► Remove and inspect the washer (3) – replace

it if it shows signs of wear.

► Install the new chain sprocket in the reverse

sequence.

23 Maintaining and Sharpen‐

ing the Saw Chain

23.1

Cutting effortlessly with a cor‐

rectly sharpened chain

A properly sharpened chain slices through wood

effortlessly and requires very little feed pressure.
Do not work with a dull or damaged chain as it

will increase the physical effort required, produce

unsatisfactory results and a higher rate of wear.

► Clean the chain.

► Check the chain for cracks in the links and

damaged rivets.

► Replace any damaged or worn parts of the

chain and match the new parts to the shape

and size of the original parts.

Carbide-tipped saw chains (Duro) are particularly

wear resistant. STIHL recommends you have

your chain resharpened by a STIHL servicing

dealer.

English

20 Motor Cooling

0458-764-0121-B

Содержание MSE 250 C





































Результаты поиска

Содержание MSE 250 C

Отзывы:

Похожие инструкции для MSE 250 C

Бренды по названию

Популярные бренды

Stihl MSE 250 C, Инструкция по эксплуатации

Результаты поиска

Содержание MSE 250 C

Отзывы:

Похожие инструкции для MSE 250 C

Бренды по названию

Популярные бренды