Stihl MSE 250 C Скачать руководство пользователя

Страница: 22 / 36

9931BA015 KN

► Pull the hand guard towards the front handle

until there is an audible click and it is in posi‐

tion

‚

– the chain brake is disengaged.

9931BA004 KN

► Depress the trigger switch lockout (1) with

your thumb.

► Squeeze the trigger switch (2) with your index

finger.

► Start the cut with the chain running.
The motor runs only if the hand guard is on

‚

and the trigger switch lockout (1) and trigger

switch (2) are operated simultaneously.

16 Switching Off

9931BA033 KN

► Release the trigger switch (2) so that it can

return to the off position. It is locked in this

position by the trigger switch lockout (1).

The coasting brake brings the chain to a stand‐

still.

WARNING

The coasting brake operates immediately only if

the trigger switch is fully released. If you release

the trigger switch slowly or only partly, the saw

chain will continue to run for several seconds.

9931BA003 KN

► Move hand guard to

– the chain is locked.

During longer work breaks – disconnect the plug

from the wall outlet.
When the machine is not in use, store it in such a

way that it does not endanger others.
Secure it against unauthorized use.

17 Overload Cutout

The overload cutout interrupts the power supply

to the saw in the case of mechanical overload

due to, e.g.

–

excessive feed force

–

"lugging down" the motor

–

pinching the saw chain in the cut

If the overload cutout has interrupted the power

supply:

► Pull the guide bar out of the cut.

► If necessary, disengage the chain brake – see

"Chain Brake".

This power tool is equipped with an electronic

overload cutout to monitor motor temperature

and power consumption.

9913BA01

1 KN

English

16 Switching Off

0458-764-0121-B

Содержание MSE 250 C





































Результаты поиска

Содержание MSE 250 C

Отзывы:

Похожие инструкции для MSE 250 C

Бренды по названию

Популярные бренды

Stihl MSE 250 C, Инструкция по эксплуатации

Результаты поиска

Содержание MSE 250 C

Отзывы:

Похожие инструкции для MSE 250 C

Бренды по названию

Популярные бренды