Stihl MSE 250 C Скачать руководство пользователя

Страница: 17 / 36

► Hold the bar nose up.

► Use a screwdriver to turn the tensioning

screw (1) clockwise until the chain fits snugly

against the underside of the bar.

► While still holding the bar nose up, tighten

down the nut firmly.

► Go to "Checking Chain Tension".
A new chain has to be retensioned more often

than one that has been in use for some time.

► Check chain tension frequently – see chapter

on "Operating Instructions".

Checking Chain Tension

9913BA006 KN

► Disconnect the plug from the wall outlet.

► Wear work gloves to protect your hands.

► Disengage the chain brake: Pull the hand

guard (1) against the front handle and hold it

there – the chain brake and coasting brake are

disengaged in this position.

► The chain must fit snugly against the under‐

side of the bar and it must still be possible to

pull the chain along the bar by hand.

► If necessary, re-tension the chain.
A new chain has to be re-tensioned more often

than one that has been in use for some time.

► Check chain tension frequently – see chapter

on "Operating Instructions".

Chain Lubricant

For automatic and reliable lubrication of the

chain and guide bar – use only an environmen‐

tally compatible quality chain and bar lubricant.

Rapidly biodegradable STIHL BioPlus is recom‐

mended.

NOTICE

Biological chain oil must be resistant to aging

(e.g. STIHL BioPlus), since it will otherwise

quickly turn to resin. This results in hard deposits

that are difficult to remove, especially in the area

of the chain drive and chain. It may even cause

the oil pump to seize.

The service life of the chain and guide bar

depends on the quality of the lubricant. It is

therefore essential to use only a specially formu‐

lated chain lubricant.

WARNING

Do not use waste oil. Renewed contact with

waste oil can cause skin cancer. Moreover,

waste oil is environmentally harmful.

NOTICE

Waste oil does not have the necessary lubricat‐

ing properties and is unsuitable for chain lubrica‐

tion.

10 Filling Chain Oil Tank

10.1

Preparations

9913BA007 KN

► Thoroughly clean the oil tank cap (1) and the

area around it to ensure that no dirt falls into

the tank.

► Position the machine so that the tank cap

faces up.

8 Checking Chain Tension

English

0458-764-0121-B

Содержание MSE 250 C





































Результаты поиска

Содержание MSE 250 C

Отзывы:

Похожие инструкции для MSE 250 C

Бренды по названию

Популярные бренды

Stihl MSE 250 C, Инструкция по эксплуатации

Результаты поиска

Содержание MSE 250 C

Отзывы:

Похожие инструкции для MSE 250 C

Бренды по названию

Популярные бренды