Stihl MSE 250 C Скачать руководство пользователя | Manualshive

Страница: 15 / 36

background image

► Tip of the guide bar must penetrate the wood

before the holding strap (4) – guide the chain‐

saw absolutely horizontally and swivel as

widely as possible

► Make the felling cut up to the hinge (5)

–

Do not cut into the hinge

► Make the felling cut up to the holding strap (6)

–

Do not cut into the holding strap.

001BA268 KN

Shout a second warning immediately before the

tree falls.

► With outstretched arms, cut through the hold‐

ing strap at a downward angle from outside.

5

Cutting Attachment

A cutting attachment consists of the saw chain,

guide bar and chain sprocket.
The cutting attachment that comes standard is

designed to exactly match the chain saw.

001BA248 KN

1

2

3

a

–

The pitch (t) of the saw chain (1), chain

sprocket and the nose sprocket of the Rollo‐

matic guide bar must match.

–

The drive link gauge (2) of the saw chain (1)

must match the groove width of the guide

bar (3).

If non-matching components are used, the cut‐

ting attachment may be damaged beyond repair

after a short period of operation.

5.1

Chain Scabbard

001BA244 KN

Your saw comes standard with a chain scabbard

that matches the cutting attachment.
If guide bars of different lengths are mounted to

the saw, always use a chain scabbard of the cor‐

rect length which covers the complete guide bar.
The length of the matching guide bars is marked

on the side of the chain scabbard.

6

Mounting the Bar and

Chain (side chain ten‐

sioner)

WARNING

Do not connect the power tool to the wall outlet

yet.

6.1

Removing the Chain Sprocket

Cover

9913BA001 KN

► Unscrew the nut and remove the chain

sprocket cover.

5 Cutting Attachment

English

0458-764-0121-B

15

«
...
13
14
15
16
17
...
»

Содержание MSE 250 C





































Отзывы:

Нет отзывов

Похожие инструкции для MSE 250 C

Бренд: Makita Страницы: 2

Бренд: Jet Страницы: 1

Instruction Manual

Бренд: Echo Страницы: 36

Бренд: Graphite Страницы: 81

Бренд: Evolution Страницы: 44

Бренд: Hercules Страницы: 60

Бренд: Milwaukee Страницы: 19

shindaiwa CSG-7410ES

Бренд: Echo Страницы: 74

Бренд: Denzel Страницы: 136

ReefKeeper DFS-100

Бренд: Inland Страницы: 4

Бренд: HADEF Страницы: 17

Бренд: EINHELL Страницы: 46

Бренд: Scheppach Страницы: 84

Бренд: GreenWorks Pro Страницы: 41

Бренд: Ryobi Страницы: 20

Бренд: Ryobi Страницы: 40

Бренд: Palmgren Страницы: 49

Powerplus XQ POWXQG4060

Бренд: VARO Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды