background image

36

English

MS 380

For periods of about 3 months or longer:

:

Drain and clean the fuel tank in a 
well ventilated area.

:

Run engine until carburetor is dry, 
this helps prevent the carburetor 
diaphragms sticking together.

:

Remove the saw chain and guide 
bar, clean them and spray with 
corrosion inhibiting oil.

:

Thoroughly clean the unit, 
pay special attention to the cylinder 
fins and air filter.

:

If you use a biological chain and bar 
lubricant, e.g. STIHL BioPlus, 
completely fill the chain oil tank.

:

Store the unit in a dry and high or 
locked location, out of the reach of 
children and other unauthorized 
persons.

:

Remove the chain sprocket cover, 
chain and guide bar.

:

Disengage the chain brake:
Pull hand guard toward the front 
handle.

Replacing the Chain Sprocket

Replace the chain sprocket after 
using two Oilomatic chains.

Replace sooner if the wear marks 
on the sprocket are deeper than 
approx. 0.5 mm since this would 
reduce the life of the chain. You can 
use a reference gauge (Special 
Accessories) to check the depth of 
the wear marks on sprockets.

It is best to use two chains in 
rotation with one sprocket.

Use only original STIHL chain sprockets 
to ensure correct operation of the chain 
brake. 

Rim Sprocket

:

Use a screwdriver to remove 
the E-clip (

1

).

:

Take off the washer (

2

). 

:

Examine the splines on the clutch 
drum – if wear marks are severe, 
install a new clutch drum.

:

Replace the rim sprocket (

3

with cavities facing outward.

:

Refit the washer and E-clip on the 
crankshaft.

Storing the Machine

Checking and Replacing 

Chain Sprocket

001BA121 KN

Содержание MS 380

















































Отзывы: