Stihl MS 361 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 44

Stihl MS 361 Скачать руководство пользователя страница 38

13 Oilomatic chain
14 Oil filler cap
15 Muffler
16 Front hand guard
17 Front handle (handlebar)
18 Starter grip
19 Fuel filler cap
20 Master Control lever
21 Throttle trigger
22 Throttle trigger lockout
23 Rear handle
24 Rear hand guard
# Serial number

30 Specifications

30.1

Engine

STIHL single cylinder two-stroke engine
30.1.1

MS 361

Displacement:

59.0 cc

Bore:

47 mm

Stroke:

34 mm

Engine power to ISO 7293: 3.4 kW (4.6 bhp) at

10,000 rpm

Idle speed:

1)

2,800 rpm

30.2

Ignition System

Electronic magneto ignition
Spark plug (resistor type): Bosch WSR 6 F,

NGK BPMR 7 A

Electrode gap:

0.5 mm

30.3

Fuel System

All position diaphragm carburetor with integral

fuel pump
Fuel tank capacity:

685 cc (0.685 l)

30.4

Chain lubrication

Fully automatic, speed-controlled oil pump with

rotary piston. Additional manual oil flow control
Oil tank capacity:

325 cc (0.325 l)

30.5

Weight

Weight (dry, without bar and chain):

MS 361:

5.6 kg

30.6

Cutting Attachment

Actual cutting length may be less than the speci‐

fied length
30.6.1

Rollomatic guide bars

Bar lengths (3/8" pitch):

37, 40, 45, 50 cm

Groove width:

1.6 mm

30.6.2

3/8" chains

Rapid Micro (36 RM) Type 3652

Rapid Micro 3 (36 RM3) Type 3664

Rapid Super (36 RS) Type 3621

Rapid Super 3 (36 RS3) Type 3626

Pitch:

3/8" (9.32 mm)

Drive link gauge:

1.6 mm

30.6.3

Chain sprocket

7-tooth for 3/8"

Max. chain velocity to ISO 1168127.5 m/s

Chain speed at maximum power

output:

21.7 m/s

30.7

Noise and Vibration Data

For further details on compliance with Vibration

Directive 2002/44/EC see www.stihl.com/vib.
30.7.1

Sound pressure level L

p

to ISO 22868

MS 361:

103 dB(A)

30.7.2

Sound power level L

w

to ISO 22868

MS 361:

115 dB(A)

30.7.3

Vibration measurement a

hv, eq

to

ISO 22867

Handle, left

Handle,

right

MS 361:

3.6 m/s

2

3.6 m/s

2

The K‑factor in accordance with Directive

2006/42/EC is 2.0 dB(A) for the sound pressure

level and sound power level; the K‑factor in

accordance with Directive 2006/42/EC is
2.0 m/s

2

for the vibration level.

30.8

REACH

REACH is an EC regulation and stands for the

Registration, Evaluation, Authorisation and

Restriction of Chemical substances.
For information on compliance with the REACH

regulation (EC) No. 1907/2006 see

www.stihl.com/reach.

1)

to ISO 11681 +/- 50 rpm

English

30 Specifications

38

0458-212-0121-C

«
...
36
37
38
39
40
...
»

Содержание MS 361













































Отзывы:

Нет отзывов