Stihl KA 120 Скачать руководство пользователя страница 16

Страница: 16 / 24

► Fit a new spark plug after about 100 operating

hours – or sooner if the electrodes are badly

eroded. Install only suppressed spark plugs of

the type approved by STIHL – see "Specifica‐

tions".

14.1

Removing the Spark Plug

► Turn off the engine.

250BA054 KN

► Pull off the spark plug boot (1).

► Unscrew the spark plug.

14.2

Checking the Spark Plug

000BA039 KN

► Clean dirty spark plug.

► Check electrode gap (A) and readjust if neces‐

sary – see "Specifications".

► Rectify the problems which have caused foul‐

ing of the spark plug.

Possible causes are:

–

Too much oil in fuel mix.

–

Dirty air filter.

–

Unfavorable running conditions.

000BA045 KN

WARNING

Arcing may occur if the adapter nut (1) is loose

or missing. Working in an easily combustible or

explosive atmosphere may cause a fire or an

explosion. This can result result in serious inju‐

ries or damage to property.
► Use resistor type spark plugs with a properly

tightened adapter nut.

14.3

Installing the Spark Plug

002BA446 KN

► Screw the spark plug (2) into the cylinder and

fit the boot (1) (press it down firmly).

15 Engine Running Behavior

If engine running behavior is unsatisfactory even

though the air filter is clean and the carburetor

and throttle cable are properly adjusted, the

cause may be the muffler.
Have the muffler checked by a servicing dealer

for contamination (carbonization).
STIHL recommends that you have servicing and

repair work carried out exclusively by an author‐

ized STIHL servicing dealer.

English

15 Engine Running Behavior

0458-516-0121-B

Содержание KA 120

























Результаты поиска

Содержание KA 120

Отзывы:

Бренды по названию

Популярные бренды

Stihl KA 120, Инструкция по эксплуатации

Результаты поиска

Содержание KA 120

Отзывы:

Бренды по названию

Популярные бренды