manualshive.com logo in svg

Stihl HL 92, Инструкция по эксплуатации

Поделиться
Скачать
Stihl HL 92 Скачать руководство пользователя страница 10

388BA033 KN

Swing the cutter bar in an arc towards the out‐

side of the hedge so that the cuttings are swept

to the ground.
Recommendation: Only cut hedges that are no

more than chest height.

4

Approved Power Tool

Attachments

The following STIHL attachments may be moun‐

ted to the basic power tool:
Attachment

Application

HL 0°, 500 mm 

1)

Long reach hedge trim‐

mer

HL 0°, 600 mm 

1)

Long reach hedge trim‐

mer

HL 145°, 500 mm 

1)

Long reach hedge trim‐

mer

HL 145°, 600 mm 

1)

Long reach hedge trim‐

mer

HT 

2)

Pole pruner

BF 

2) 3)

Cultivator with pick tines

SP 10

Special harvester

5

Assembling the Unit

5.1

Mounting the Loop Handle

(HL 92, HL 94)

Loop handle is required on versions with long

drive tube (HL 92, HL 94).

7
8

2

1

6

7
8

9

9

3

5

4

0000-GXX-1679-A0

► Place the clamp (1) in the loop handle (2) and

position them both against the drive tube (5)

between the carrying ring (3) and handle

hose (4).

► Position the clamp (6) against the shaft.

► Line up the holes.

► Insert the screws (7) with washers (8).

► Fit the square nuts (9) and screws.

1)

Loop handle required on versions with long drive tube (HL 92, HL 94)

2)

Not approved for versions with short drive tube (HL 92 K)

3)

Loop handle required

English

4 Approved Power Tool Attachments

10

0458-519-8321-D

Содержание HL 92





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды