manualshive.com logo in svg

Stihl 561 C-M, Инструкция по эксплуатации, Страница: 21 / 28

Поделиться
Скачать
Stihl 561 C-M Скачать руководство пользователя страница 21

Fault

Cause

Remedy

The engine does not

start.

There is not enough

fuel in the fuel tank.

► Prepare fuel mix and refuel the trimmer.

 

The engine has floo‐

ded.

► Vent the combustion chamber.

The carburetor is too

hot.

► Allow trimmer to cool down.

► Depress the manual fuel pump at least 10 times

before starting the engine.

The carburetor has

iced up.

► Allow trimmer to warm up to +10°C.

The engine idles

erratically.

The carburetor has

iced up.

► Allow trimmer to warm up to +10°C.

The engine stops

while idling.

The carburetor has

iced up.

► Allow trimmer to warm up to +10°C.

The engine does not

reach maximum

speed.

Trimmer is not cor‐

rectly tuned to ambi‐

ent conditions.

► Calibrate the trimmer.

18.2

Replacing air filter

The air filter cannot be cleaned. The air filter

must be replaced if it is damaged or there is a

loss of engine power.

► Shut off the engine.

2

3

1

0000097407_001

► Take out the screws (1) and remove the filter

cover (2).

► Clean the area around the air filter (3) with a

damp cloth or a soft brush.

► Take out the air filter (3).

► Install the new air filter (3).

► Fit the filter cover (2).

► Insert screws (1) and tighten.

18.3

Venting the Combustion Cham‐

ber

2

1

4

5

3

0000097408_001

► Turn screw (1) counterclockwise.

► Lift the cover (2) and push it backwards.

► Pull off the spark plug boot (3).

► Unscrew the spark plug (4).

► Dry the spark plug (4).

WARNING

■ If the starter grip is pulled out while the spark

plug boot is removed, sparks may escape.

Sparks may cause fires and explosions in

highly flammable or explosive environments.

Persons may be seriously or fatally injured

and property may be damaged.

► Depress the stop switch and keep it

depressed before pulling the starter grip.

► Depress the stop switch and hold it in that

position.

► Pull the starter grip (5) several times and

guide it back slowly.

You have vented the combustion chamber.

► Insert and tighten down the spark plug (4)

firmly.

► Press the spark plug boot (3) firmly home.

► Install cover (2) and tighten screw (1).

19 Specifications

19.1

Brushcutter STIHL FS 511 C-M

–

Displacement: 51.6 cm³

–

Engine power to ISO 8893: 2.4 kW (3.3 bhp)

at 9,500 rpm

–

Idle speed : 2,500 rpm

–

Max. output shaft speed: 7,890 rpm

–

Approved spark plug: NGKBPMR7A from

STIHL

–

Electrode gap of the spark plug: 0.5 mm

–

Dry weight without cutting attachment and

deflector: 10.2 kg

19 Specifications

English

0458-856-0121-A. VA0.B21.

21

Содержание 561 C-M





























Отзывы:

Нет отзывов