manualshive.com logo in svg

Stiga TC 108 SD, Руководство по ремонту, Страница: 44 / 79

Поделиться
Скачать
Stiga TC 108 SD Скачать руководство пользователя страница 44

WORKSHOP MANUAL

Map of functional units

TC 108 SD  -  TC 118 SD

The transmission unit (11) is supported by a holder 

(12) fixed by a screw with nut (13) and is fixed to the 

chassis by four screws with relative nuts (14).

Undo  the  nut  (13)  and  then  carefully  undo  the  four 

lower nuts (14), holding up the unit so that it does not 

fall.

   Remove the rear part of the wheel cover

   Remove the rear tank (if installed)

   Lift the rear part of the machine

   Remove the rear wheels.

Working from the rear section, grasp the two branch-

es of the belt (1), pulling it just enough to free it from 

the pulley throat (2), overcoming the resistance of the 

idler pulley spring.

Remove the drive control rod (3) by unscrewing the 

relative pin nut (4) and the brake rod (5) by un screwing 

the nut (6) under the lever.

General informations

The rear axle (Transaxle) is made up of a single 

maintenance free sealed unit which includes the 

transmission unit (hydrostatic) and the differen­

tial and doesn’t need any maintenance. 

It only needs to be removed to be replaced or for 

an overhaul by the Manufacturer’s Service Cen­

tre.

Related topics

[  2.3]

  

Lifting of the machine

[  4.2]

  

Brake adjustment

[  4.4]

  

Drive pedal adjustment

[  5.2]

  

Removal of the rear cover

[  5.7]

  

Removal the rear tank (if present)

[  6.1]

  

Removal of the wheels

Tightening torques

13

  Rear axle support nut  .................. 25 ÷ 30 Nm

14

  Rear axle fastening nuts  .............. 25 ÷ 30 Nm

REMOVAL OF THE REAR AXLE

(Tuff Torq K46F)

CHAPTER

REVISION

FROM ...

PAGE

5.5

0

2018

1 of 2

Содержание TC 108 SD
















































































Отзывы:

Нет отзывов