background image

— 1 —

Installation and Operation Manual

STI 4-Channel Receiver

Thank you for purchasing the STI 4-Channel Receiver. Your satisfaction is very important to us. 

How the Product Works

STI offers multiple wireless products designed to alert you of several different conditions.  The 
4-Channel Receiver allows you to monitor up to 4 different STI sensors at a single convenient 
location.  The STI wireless alert series uses a system to ensure other non STI sensors are not 
enrolled.  The STI 4-Channel Receiver allows you to latch any alert until reset.

Before You Start

Make sure to read all instructions per task prior to beginning. Refer to this drawing to become 
familiar with all parts.

Model:  

STI-34104

STI-30104

LAMP CONTROLLER

(OPTIONAL)

AC ADAPTER

GREEN

LED

TRANSISTOR

OUTPUT JACK

RECEIVER ANTENNA

SPEAKER

STI-34104

INDOOR RECEIVER

BUTTON

RED LED

SENSOR TRANSMITTER CAP

SENSOR TRANSMITTER BASE

MOUNTING

TUBE CAP

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

2 “C” BATTERIES
(NOT INCLUDED)

SENSOR TRANSMITTER

12”MOUNTING TUBE

MOUNTING STAKE

SENSOR TRANSMITTER

BOTTOM

SENSOR TRANSMITTER

MOUNTING

TUBE CAP

MOUNTING STAKE

SENSOR TRANSMITTER BOTTOM

SCREWS

RECHARGEABLE NiMH BATTERIES

H

L

SENSITIVITY JUMPERS

(SOLAR TYPE)

SENSITIVITY JUMPERS

(BATTERY TYPE)

H

L

FINGER

NOTCHES

REMOVE PLASTIC TAB
FROM BATTERIES

DRIVEWAY

3’OR

LESS

25' OR MORE

PLACE SENSOR 
TRANSMITTER 3' OR 
LESS FROM EDGE OF 
DRIVEWAY AND 25'
OR MORE FROM STREET.

12’

MAX

DRIVEWAY

PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF 
DRIVEWAY AND 25+ 
FEET OR MORE FROM
STREET.

25' OR MORE

 3' OR

LESS

12' 

MAX

+

+

-

B

DETAIL B

SCALE 2:1

B

C

H

L

-

+

+

-

B

-

FINGER NOTCHES

DO NOT

PULL ANTENNA!

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

SENSITIVITY

ADJUSTMENT

SENSITIVITY

ADJUSTMENT

POWER CONNECTOR

ANTENNA CONNECTOR

12”MOUNTING TUBE

GREEN

LED

TRANSISTOR

OUTPUT JACK

RECEIVER ANTENNA

SPEAKER

BUTTON

RED LED

POWER CONNECTOR

ANTENNA CONNECTOR

4-Channel Receiver STI-34104

Receives up to 4 different STI Wireless Alert Series Sensors

Program a Sensor

1.

  Plug antenna into the antenna (red) connector on the receiver.

2.

  Plug adapter into the wall.  

3.

 While holding down the receiver button, plug the adapter into the 4-Channel 

Receiver.

  A series of beeps/tones will begin playing. Release button when beeps/tones 

finish. The red and green LED’s will flash quickly. The receiver is now in program mode and 
you have 1 minute to program all sensors.

4.

  Activate a sensor

 to program into 4-Channel (refer to your sensor instructions).  A tone or 

series of beeps will sound representing the channel the sensor programmed into (i.e.: one 
beep is zone 1, two beeps is zone 2, etc.). 

5.  If more sensors are to be programmed, repeat step 4.
6.  After programming sensor(s), wait a minimum of 5 seconds, press receiver button to exit 

Program Mode or receiver will exit program mode automatically within one minute.

Содержание STI-34104

Страница 1: ...OR MORE PLACE SENSOR TRANSMITTER 3 OR LESS FROM EDGE OF DRIVEWAY AND 25 OR MORE FROM STREET 12 MAX POWER CONNECTOR ANTENNA CONNECTOR 4 Channel Receiver STI 34104 Receives up to 4 different STI Wireless Alert Series Sensors Program a Sensor 1 Plug antenna into the antenna red connector on the receiver 2 Plug adapter into the wall 3 While holding down the receiver button plug the adapter into the 4 ...

Страница 2: ... down the receiver button until you hear a single beep approximately 3 seconds Red LED will be on solid Entering Permanent Silent Mode Press and hold down the receiver button until the receiver makes a series of two short beeps approximately 6 seconds Red LED will be on solid Exit both Silent Modes Press and hold down the receiver button until you hear a single beep to return to normal operating m...

Страница 3: ...k the AC power outlet for power 2 Check that the AC Adapter is plugged into both the receiver and wall outlet 3 Try another AC adapter 12V DC 100mA only with a 12 VDC center and 12 VDC outside edge The receiver does not sound when a sensor is activated 1 Check that the receiver is not in Temporary or Permanent Silent Mode 2 Move the sensor close to the receiver and test If alert sounds on the rece...

Страница 4: ...eas To prevent electric shock match wide blade of plug to the wide slot of outlet and insert completely When using lamp controller option use ONLY 200 Watt or less incandescent lamps and keep lamp away from bed coverings curtains or other flammable materials as this may present a fire hazard Warranty Information Safety Technology International Inc warrants to the original consumer purchaser that t...

Отзывы: