Stewart MacDonald Erlewine Neck Jig Скачать руководство пользователя страница 1

Страница: 1 / 9

21 N. Shafer St. Athens, OH 45701

21 N. Shafer St. Athens, OH 45701
800-848-2273

800-848-2273 Fax:

Fax: 740-593-7922

740-593-7922

stewmac.com

page 1 of 9

aiin

n b

Crro

ossssb

arrs

s ((3 )

3 )

Angle supports (3)

Urethane pads for levelers and peghead jack (7)

Allen wrenches (4)

Wood support slats with cork pads (4)

Body straps (2)

Body levelers (6)

Dial indicators (2)

Neck supports (3)

Peghead puller

with strap

Peghead jack

Eyebolt hanger

How to assemble the Neck Jig

Install an a

Install an angle support in each

ngle support in each of the three

of the three crossbars.

crossbars.

The T-shaped sliders ﬁt

The T-shaped sliders ﬁt the crossbars, and the

the crossbars, and the square nuts

square nuts

are for mounting to t

are for mounting to the main beam.

he main beam. Tw

Two of the crossbars

o of the crossbars

have etched centering scales, which should

have etched centering scales, which should face upward.

face upward.

Sheet

Sheet #i-5399

#i-5399 04/2014

04/2014

Erlewine Neck Jig

Attach the crossbars to the main beam using the squa

Attach the crossbars to the main beam using the square

nuts. The shortest bar provides support near the ne

nuts. The shortest bar provides support near the ne ck joint

ck joint

and should be instal

and should be installed ﬁrst.

led ﬁrst. The longest bar supports the

The longest bar supports the

tail end of the instrument and should be installed last.

Square nut for main beam

T-shaped sl

T-shaped slider

ider

Instructions

Содержание Erlewine Neck Jig










Результаты поиска

Содержание Erlewine Neck Jig

Отзывы:

Похожие инструкции для Erlewine Neck Jig

Бренды по названию

Популярные бренды

Stewart MacDonald Erlewine Neck Jig, Инструкция по эксплуатации

Результаты поиска

Содержание Erlewine Neck Jig

Отзывы:

Похожие инструкции для Erlewine Neck Jig

Бренды по названию

Популярные бренды