Steris P920011-649 Скачать руководство пользователя страница 72

Страница: 72 / 168

4-27

Processing Instructions

Operator Manual

920011-649

4.7 Pre-Processing

Checklist

The following conditions are necessary to achieve successful

processing of the endoscopes and accessory types listed in the

Endoscope Quick Reference Guide

– ENDOSCOPE PREPARATION –

Endoscope and accessories were:

�

inspected and found to be in proper working order;

�

prepared for immersion;

�

successfully leak-tested;

�

manually pre-cleaned within 30 minutes prior to starting

processing cycle.

– PRIOR TO PROCESSING –

�

Debris screen

is clear of debris (see

);

�

Spray arms

rotate freely (see

);

�

Accessories

are correctly positioned in

endoscope processing

support

(see

);

�

Insertion tube sleeve

(labeled with a RED dot, labeled with a

BLUE dot or NOT labeled)

is used for endoscopes which can

be inserted into one of three template slots located in front of

endoscope processing support. If required, place proper

insertion tube sleeve into control handle boot "A" and/or "B" (see

);

�

Endoscope #1

is placed in control handle boot "A" (see

);

�

endoscope #1 does not have a light guide cable

, a

control handle boot plug is placed in the universal cord port;

�

Endoscope #2

is placed in control handle boot "B" (see

);

�

endoscope #2 does not have a light guide cable

, a

control handle boot plug is placed in the universal cord port;

�

only one endoscope is processed

, the endoscope is placed

in control handle boot "A" and a control handle boot plug is

placed in the fluid delivery port of control handle boot "B";

�

only accessories, such as dilators and bougies, are being

processed (without an endoscope)

, test cords are placed in

both control handle boots (follow instructions in

Endoscope

Quick Reference Guide

for Flow Unit 5)

;

�

If required,

Flow Units

are attached (refer to

Endoscope Quick

Reference Guide

);

Содержание P920011-649









































































































































































Результаты поиска

Содержание P920011-649

Отзывы:

Steris P920011-649, Руководство оператора, Страница: 72 / 168

Результаты поиска

Содержание P920011-649

Отзывы: