manualshive.com logo in svg

Steris HarmonyAIR G Series, Руководство оператора

Поделиться
Скачать
Steris HarmonyAIR G Series Скачать руководство пользователя страница 51

6-1

Maintenance

Operator Manual

10043124

6.1  Preventive

Maintenance

1.

Regular service and maintenance MUST be performed only by 
STERIS or a STERIS-trained technician. Any work performed by 
inexperienced or unqualified persons or the installation of 
unauthorized parts could cause personal injury, invalidate the 
warranty or result in costly damage.

2.

Under no circumstances should this equipment be serviced 
without the Maintenance Manual. The Maintenance Manual can 
be purchased by contacting STERIS Customer Service.

3.

A detailed Preventive Maintenance schedule and replacement 
parts list can be found in the Maintenance Manual. The 
Maintenance Manual can be purchased by contacting STERIS 
Customer Service.

4.

Preventive Maintenance is essential in keeping this equipment in 
optimal working condition. STERIS recommends establishing an 
annual maintenance agreement with STERIS service.

5.

Preventive Maintenance and regular service must be performed 
according to the Maintenance Manual in order to comply with the 
requirements for essential performance and compliance with 
electromagnetic compatibility.

Important: 

Use only authorized STERIS replacement parts when

conducting any maintenance on the equipment.

NOTE: Refer to the HarmonyAIR Surgical Lighting System G Series
Installation Instructions (10043123) and HarmonyAIR Surgical
Lighting System G Series Maintenance Manual (P764335-779) to
safely replace components.

6.2  Inspect

Suspension

Start at the highest point on the suspension, and work out toward the
lightheads on each suspension arm. Verify proper operation of each
braking point. If necessary, adjust each of the brakes in turn, with the
goal of eliminating both binding and drift in the system. Refer to
Maintenance Manual, if necessary.

WARNING – SHOCK AND BURN HAZARD: Disconnect all utilities to lighting fixture before 
servicing. Do not install the lighting fixture unless all utilities have been properly locked out. 
Always follow OSHA Lockout-Tagout and electrical safety-related work practice standards.

WARNING – ELECTRIC SHOCK HAZARD:
• Do not remove covers or perform service other than as described in this operator manual. Refer 

servicing to qualified service personnel.

• The OFF position on the system ON/OFF touch pad of the wall control turns off control to 

camera and lightheads, but system is still energized. This mode is referred to as STANDBY, and 
the ON/OFF LED flashes once per second while system is in this mode.

WARNING – PERSONAL INJURY HAZARD AND/OR EQUIPMENT DAMAGE HAZARD:

• Do not attempt to clean lighthead unless lighthead is turned off and has cooled sufficiently.

• Do not attempt to adjust suspension system. Refer servicing to qualified service personnel.

• No part of this system shall be serviced while in use with a patient.

!

!

!

MAINTENANCE

6

Содержание HarmonyAIR G Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды