Steris AMSCO 400 Series Скачать руководство пользователя страница 140

Страница: 140 / 174

8-10

P129394-020

Operator Manual

Routine Maintenance

Install left end of cartridge first, then push right end in, snapping
it into place.

Re-tighten ribbon by rotating wheel on left side of cartridge 1/4
turn. Then see

, through

, to reinstall take-up spool.

8.5 Waste Products

Disposal

The following are waste materials associated with the sterilizer. When
disposing of waste materials, be compliant with federal, state and
local regulations.

•

Printer paper – recyclable.

•

Printer ribbon – not recyclable.

•

Water filters – not recyclable.

•

Waste water – 57 L/min (15 gal/min).

Entire sterilizer (end-of-life) – Contact STERIS Corporation for
disposal or recycling recommendations.

8.6 Recommended

Spare Parts

To order replacement parts and/or supply products, proceed as
follows:

Include the description and part/order number as listed in

Table 8-2

Include the model and serial numbers of your sterilizer on your
order.

Send your order directly to the sales and service center serving
your area.

Contact your sales representative for recommendations on cleaning
products, biological indicators or parts not listed in

Table 8-2

NOTE: Use only STERIS authorized parts on this equipment. Use
of unauthorized parts will void the warranty.

Содержание AMSCO 400 Series















































































































































































Результаты поиска

Содержание AMSCO 400 Series

Отзывы:

Бренды по названию

Популярные бренды

Steris AMSCO 400 Series, Руководство оператора

Результаты поиска

Содержание AMSCO 400 Series

Отзывы:

Бренды по названию

Популярные бренды