background image

WARRANTY

This Steren product is warranted under normal usage against defects in 

workmanship and materials to the original purchaser for one year from the 

date of purchase.

CONDITIONS

1.- This warranty card with all the required information, invoice or purchase 

ticket,  product  box  or  package,  and  product,  must  be  presented  when          

warranty service is required.

2.- If the product stills on the warranty time, the company will repair it free 

of charge.

3.- The  repairing  time  will  not  exceed  30  natural  days,  from  the  day  the 

claim was received.

4.-  Steren  sell  parts,  components,  consumables  and  accessories  to                

customer, as well as warranty service, at any of the addresses mentioned 

later.

THIS WARRANTY IS VOID IN THE NEXT CASES:

If the product has been damaged by an accident, acts of God, mishandling, 

leaky batteries, failure to follow enclosed instructions, improper repair by 

unauthorized personnel, improper safe keeping,   among others.
a)  The  consumer  can  also  claim  the  warranty  service  in  the  purchase             

establishment.

b) If you lose the warranty card, we can reissue it, if you show the invoice 

or purchase ticket.

In case your product fails or have questions,

please contact your nearest dealer.

If you are in Mexico, please give a call to our Call Center.

Call Center 

 

01 800 500 9000

Product: Bike LED lamp set

Part number: LAM-227

Brand: Steren

Before using your new Electronic insect killer, please read this  

instruction manual to prevent any damage. Put it away in a 

 

Product design and specifications are subject to change     

without previous notice.

IMPORTANT

• Do not expose your equipment to extreme temperatures. 

• Always use a smooth, clean and dry cloth to clean the equipment.

• When the lamp remains without use for long periods of time, make sure to 

remove the batteries. 

Lantern

Input: 

4.5V

 (3xAAA)

Nominal consumption: 816 Wh/day

The lamp does not light  

 

- Press the button on and off.

 

 

 

 

- Check the battery polarity.

 

 

 

 

- Replace batteries.

1. Lamp.

2. ON/OFF button.

3. Battery compartment.
4. Strap.

Front lamp

1. Unscrew the battery top.

2. Take out the battery container.

3. Place 3 batteries type AAA inside the battery compartment. Pay attention 

in the polarity.

4. Insert the battery container into the lamp following the arrow direction.

Back lamp

1. Lift up the lamp top to lever, first pull up from one side.

2. Carefully remove the two plastic parts on the battery compartment.

3. Place 2 batteries type AAA inside the battery compartment. Pay attention 

in the polarity.

4. Introduce the two plastic parts again and close the lamp top.

 

NOTE: Take care that the seal stays in place.

PARTS

BATTERY INSTALLATION

SPECIFICATIONS

TROUBLESHOOTING

OPERATION

Forward lamp´s support

1. Loose the upper screw from the support 

for introduce the forward lamp. Make sure 

to introduce the strap first.

2. Push the lamp inside the support.

3. Screw again  making sure that the lamp 

does not get out.

4.  To  place  the  support  on  the  handlebar,      

totally  remove  the  lower  screw  to  allow  a 

wide opening.

5. Introduce the handlebar in the opening.

6. Screw again the support making sure that 

the lamp is not moving.

7. Turn on the light.

If you press the button once, the lamp will light continuous.

If you press the button twice, the lamp will turn off.

Back lamp´s support

1. Remove the screw on the right side of the support.

2. Place the support in the stem and arrange the support in 

the height you wish.

3. Screw very well making sure that the support is not moving.

4. Identify the back clip on the lamp.

5. Identify the clip in the lamp´s support.

6. Place the clip lamp´s support on the lamp´s clip. Bottom-up 

slide, and hear “click” that indicating that the lamp is secure.

7. Turn on the light.

If you press the button once, the lamp will light continuous.

If you press the button twice, the lamp will light slowly.

If you press the button thrice, the lamp will turn on and off quickly.

If you press the button four times, the lamp will turn off.

Preventive

Input: 

3V

 (2xAAA)

Nominal consumption: 233 Wh/day

Stand-by power consumption: not 

applicable

Stand-by power consumption: not 

applicable

Before using your new Steren LED & magnifier SOS lamp, 

please read this instruction manual to prevent any damage.

Put it away in a safe place for future referen

Отзывы: