STEMCenter USA Pi-Bot v2.00 Скачать руководство пользователя | Manualshive

Страница: 89 / 110

background image

89

Basic Line Following Program

We will now discover how the line sensors will allow your Pi-Bot to detect and track a line.
Line following consists of two parts:

1.

Determining the position of your Pi-Bot to a black line

First, your Pi-Bot determines its position relative to a black line with the use of line sensors,
located in the front. When the line sensor detects black, sensor outputs “1” indicating that most
of the light is absorbed. When the line sensor detects white, the sensor output is “0.”

By using three line sensors, your Pi-Bot will know whether it is on a black line (left and right
sensors output “0” and the center sensor outputs “1”), to the left of a black line, or to the right
of a black line.

2.

Motor control

With this information, your Pi-Bot will control the speed of each motor individually to try and
get back over the line.

The diagram below visualizes parts 1 and 2.

«
...
87
88
89
90
91
...
»

Содержание Pi-Bot v2.00















































































































Отзывы:

Нет отзывов

Похожие инструкции для Pi-Bot v2.00

COMPUTING ROBO MOBILE SET

Бренд: fischertechnik Страницы: 56

Бренд: SuperDroid Robots Страницы: 6

Omni Drive Module

Бренд: neobotix Страницы: 28

Бренд: neobotix Страницы: 36

Бренд: PadBot Страницы: 33

Бренд: Janome Страницы: 114

Бренд: ABB Страницы: 82

Бренд: ABB Страницы: 660

Бренд: Heath Zenith Страницы: 48

Бренд: Aus Electronics Direct Страницы: 8

Бренд: ABB Страницы: 72

CODINGS & ROBOTICS KIT Quirkbot

Бренд: Strawbees Страницы: 12

Бренд: Petronics Страницы: 24

Бренд: Picaxe Страницы: 33

Бренд: Plum Geek Robotics Страницы: 64

Бренд: Mitsubishi Страницы: 69

Бренд: Mitsubishi Страницы: 95

Бренд: Mitsubishi Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды