SteelMax Torch Runner Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 42

background image

Torch Runner (HS)

Torch Runner (HS) Operator’s Manual

26

5.13. Gas manifold (for oxy-fuel cutting)

Provides

safe

gas delivery to 2- or 3-hose torches. Manifolds are available with or

without gas cut-off valve in both metric and imperial versions.

2/3 manifold with cut-off valve
(metric):
RZD-0475-66-00-00-0

3/3 manifold with cut-off valve
(metric):
RZD-0475-72-00-00-0

1/4’’ RH

2/2 manifold (metric):
RZD-0475-64-00-00-0

2/3 manifold (metric):
RZD-0475-63-00-00-0

2/2 manifold with cut-off valve
(metric):
RZD-0475-65-00-00-0

3/3 manifold (metric):
RZD-0475-74-00-00-0

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

«
...
24
25
26
27
28
...
»

Содержание Torch Runner











































Отзывы:

Нет отзывов

Похожие инструкции для Torch Runner

Бренд: Daewoo Страницы: 33

Бренд: EUROM Страницы: 28

Бренд: Horizon Fitness Страницы: 412

Бренд: Toro Страницы: 24

Бренд: Lincoln Electric Страницы: 94

Бренд: Dolmar Страницы: 64

SIMPLEX V-Groover 703

Бренд: Logan Graphic Products Страницы: 8

Бренд: Logan Graphic Products Страницы: 8

Бренд: ST. SpA Страницы: 44

Бренд: ES manufacturing Страницы: 5

Бренд: Poulan Pro Страницы: 38

Бренд: Valex Страницы: 48

Бренд: PERFORMANCE ADVANTAGE COMPANY Страницы: 2

Бренд: TSI Instruments Страницы: 17

Бренд: AGT Страницы: 20

professional brushcutter TBC-600

Бренд: Tanaka Страницы: 16

Бренд: Tanaka Страницы: 17

Бренд: PAPILLON Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды