Steca coolcept StecaGrid 1500 Скачать руководство пользователя страница 63

Страница: 63 / 94

Fault rectification

Faults are indicated by event messages as described below. The

display flashes red. The list of event messages below contains

information on troubleshooting and fault correction.

Event messages contain the following information:

①

Symbol for the type of event message

②

Date/time when the event occurred

③

ACTIVE

= cause of the event message is still present or

Date/

time

at which the cause of the event message was corrected.

④

Cause of the event message

⑤

Counter: No. of the displayed event messages / Total number of

event messages; max number of all event messages = 30

⑥

NEW

is displayed until the event message has been manually

confirmed via the

ESC

button.

Event message types

Type Information (symbol )
The inverter has detected an error that does not affect the feed-

in process. The user does not need to intervene.

Type Warning (symbol

)

The inverter has detected an error that may result in reduced

yields. It is highly recommended that you correct the cause of

the error.

Type Error (symbol )
The inverter has detected a serious error. The inverter will not

feed into the grid while this error is present. Please contact your

installer. More information is provided in the table below.

Display behaviour

New event messages are displayed immediately. The messages

disappear after they have been confirmed or their causes have been

corrected.

Note
When an event message is confirmed, the user

thereby simply confirms that he/she has seen the

message. This does not correct the error that caused

the event message to be shown!

If messages exist whose cause has been corrected but have not been

confirmed then

is shown in the status display. If an already

confirmed error recurs then it is displayed again.

Confirming event messages

✔

An event message with the comment

NEW

is displayed.

Press

ESC

. The event message is confirmed.

Structure

Function

Operation

747,431 | Z09.2 | 18/02/2016

Содержание coolcept StecaGrid 1500































































































Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды

Steca coolcept StecaGrid 1500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды