Steca coolcept StecaGrid 1500 Скачать руководство пользователя страница 38

Страница: 38 / 94

NOTICE!
Risk of damage to the inverter and the modules.

Connect the opposing connectors for the DC

connections to the DC cable, observing the correct

polarity.

Attach the connector plug counterparts to the DC cable

according to the manufacturer's instructions; see Appendix.

4.5 Preparing the data connection cable

If a data connection is required, use a standard RJ45 cable

(patch cable, Cat5) or construct an alternative data

connection cable(see

further information on page 28).

4.6 Connecting the inverter inverter and switching the AC on

DANGER!
Risk of death by electrocution! Observe the hazard

warnings under

Chapter 4.1 ‘Safety measures

during installation’ on page 31.

NOTICE!
–

Between the data connection cables (RS485/

Ethernet) and the DC/AC lines, maintain a

distance of 200 mm, to avoid interference in the

data transmission.

–

The protection class IP65 for type coolcept-x is

only ensured if the AC and DC plugs are plugged

in and the RJ45 sockets are sealed with sealing

caps.

If necessary, establish the data connection:

Connect the inverters and the master with data

connection cables.

On the last inverter, switch on the termination (slide

switch).

Seal open RJ45 sockets with sealing caps.

Forcefully press the plug connector mating piece (DC cable)

into the DC connection on the inverter until it audibly locks in

place.

Plug the AC connector onto the coupling on the inverter, until

the plug audibly locks in place.

747,431 | Z09.2 | 18/02/2016

Содержание coolcept StecaGrid 1500































































































Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды

Steca coolcept StecaGrid 1500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды