State Water Heaters GPO 69-700(A) страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 24

background image

18

TWO TEMPERATURE-ONE HEATER HIGH TEMPERATURE STORAGE

WITH RECIRCULATION OF SANITIZING LOOP

NOTE 1: TOGGLE SWITCH CONTROLS 180°F WATER CIRCULATION.

INSTALL ON OR CLOSE TO DISHWASHING MACHINE .
TOGGLE SWITCH MUST BE CLOSED (ON) DURING THE
RINSE OPERATION AND OPEN (OFF) WHEN DISHWASHER
IS NOT OPERATING.

NOTE 2: INSTALL LINE TEMPERATURE CONTROL IN AN

UNINSULATED TEE BEYOND THE DISHWASHING
MACHINE TAKEOFF IN THE SANITIZING LOOP. CONTROL
SHOULD BE SET AT 185°F (85°C).

NOTE 3: ADJUST PLUG COCK SO THE SANITIZING LOOP FLOW

RATE DOES NOT CAUSE UNNECESSARY TURBULENCE
IN THE TANK.

NOTE 4: IF TEMPERED WATER IS RECIRCULATED, RETURN LINE

SHOULD BE CONNECTED AT POINT "A".

WIRING DIAGRAM FOR 180° LOOP (IF USED)

INSET A

INSTALL THERMAL EXPANSION
TANK IN COLD WATER SUPPLY
LINE, IF CHECK VALVE OR
PRESSURE REDUCING VALVE IS
USED IN SUPPLY.

INSET B

VACUUM RELIEF VALVE

INSTALL PER LOCAL CODES.

NOTES

«
...
16
17
18
19
20
...
»

Содержание GPO 69-700(A)

























Отзывы:

Нет отзывов

Похожие инструкции для GPO 69-700(A)

Бренд: Danfoss Страницы: 72

Бренд: Danfoss Страницы: 91

Бренд: salmson Страницы: 12

Бренд: AL-KO Страницы: 144

Бренд: Acquaer Страницы: 12

Бренд: UNITED Страницы: 8

Бренд: DAXOM Страницы: 20

Бренд: Jandy Страницы: 24

Бренд: KALOS Страницы: 8

Softheat EBHN500

Бренд: Cadet Страницы: 10

Бренд: VARISCO Страницы: 18

Бренд: A.O. Smith Страницы: 28

Бренд: Annovi Reverberi Страницы: 100

Scalekleen EV9796-01

Бренд: Everpure Страницы: 2

Бренд: Halsey Taylor Страницы: 8

Бренд: CASELLA CEL Страницы: 27

Бренд: Inelco Страницы: 23

Бренд: Kelvinator Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды