background image

1

1

The storage tank is sold as a component part.  It has been
factory equipped with a booster element, and thermostat with
high limit.

The tank is designed to store potable water within the limits
listed on the rating plate and to supply domestic hot water up to
the element’s heating capability.

This manual contains basic instructions for the installation,
operation and maintenance of the storage tank only.  Read it
carefully before using the tank, then keep it handy for quick
reference.

If the tank leaks or the element fails to operate, all technical and
warranty questions should be directed to the local dealer from
whom the tank was purchased.  If you are unsuccessful, please
write to the company listed on the warranty sheet which came
with the tank.

  WARNING

Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to
this manual. For assistance or additional information consult
a qualified installer, service agency or the local utility.

RATING PLATE

A rating plate identifying the manufacturer of the tank will be
found above the drain valve.  When referring to the tank,
always have the information listed on the rating plate readily
available.

Fill in that information here:

MODEL NO. _______________________________________

SERIAL NO. _______________________________________

INSTALLATION DATE: ________________________________

THE MANUFACTURER OF THIS TANK WILL NOT BE LIABLE FOR ANY DAMAGE DUE TO FAILURE TO FOLLOW THESE

INSTALLATION AND OPERATING INSTRUCTIONS.

PRINTED 0108

198067-000

GEOTHERMAL STORAGE TANKS

 INSTALLATION  •  OPERATION  •  MAINTENANCE

INSULATING JACKETS:

When installing an external insulation jacket on the tank:

DO NOT cover the temperature-pressure relief valve.

DO NOT cover the instruction manual. Keep it on the
side of the water heater or nearby for future reference.

DO obtain new warning and instruction labels from
the manufacturer for placement on the blanket directly
over the existing labels.

Failure to follow these instructions can result in serious
personal injury or death.

Month

Day

Year

Instruction Manual

 WARNING

Содержание 198067-000









Отзывы: