3 А
E9
V
2
X1
X2
X3
X4
X5
X1
86
30
85
87
87а
(
–
)
(
+
)
10 А
86
30
85
87
87а
86
30
85
87
87а
+12 V
(
–
)
(
+
)
(
–
)
(
+
)
30 А
+ 12 V
blue
-whit
e
blue
-black
re
d
yello
w
gr
een
blue
or
ange
gr
een-black
gr
een-
whit
e
black
-y
ello
w
30 А
LIN A
CAN-L B
LIN B
CAN-L A
CAN-H A
CAN-H B
X2
LIN C
LIN D
ACC / Starter protection output (200 мА) (–)
Starter protection / ACC output (200 мА) (–)
868 MHz transceivers
Bluetooth transceiver
USB-connector
Autostart connection diagrams
Starter
Ignition 1
Ignition 2
Accessories
+12 V
orange-violet
orange-white
blue-red
pink
yellow
gray-black
green-yellow
black-red
yellow-white
black-white
black
red
gray
green
orange-gray
yellow-red
blue-black
yellow-black
blue
Security – telematic
system connection diagram
Connect actuators
in parallel
command
«Close»
command
«Open»
purple
Valet button with LED
Temperature sensor
Mounting recommendations
Mount the main unit at a distance not less 10 cm from the
metal surfaces, to avoid Bluetooth and RF 868 MHz signal
transmission interference.
For the cars equipped with CAN/LIN bus make a connection via the embedded digital CAN/LIN
interface, for the elder cars make an analogue connection.
Find information and wiring tips on vehicles and features supported with CAN/LIN connection at
can.starline.ru
Common
Blocking relay
in the set
NC
NO
Ignition 1
Storage battery
Door open simulation output (200 mA) (–)
Unit power supply
Engine blocking output (200 mA) (–)
Comfort closure output (200 mA) (–)
Engine run control input
Ignition input (+)
Bypass module control output (200 mA) (–)
Parking brake input (–)
R4 code relay control output (200 mA) (–)
Trunk trigger input (–)
Siren control output (2 A) (+)
Brake pedal input (+)
Trunk unlock output (200 mA) (–)
Door trigger input (+/–)
Door two-step unlock output (200 mA) (–)
Hood trigger input (–)
General installation specifications
The security system is designed for installation on vehicles with 12V on board voltage.
Prior to installation, make sure that the vehicle equipment circuits, to which the system is connected, are in suitable operating condition and no any trouble codes and check engine are indicated.
The system installation should be carried out according to the connection diagram.
The "ground" wire of the main unit should be connected first to a car body ground with an original screw.
Mount the wiring far from sources of electrical interference: ignition coils, high-voltage wires, etc.
Make sure that the harness is not lay in contact with the moving parts of the vehicle: pedals, steering shaft etc.
Connect all the harness to the main unit sockets only after all wires mounting is complete.
Do no fit the engine temperature sensor near the exhaust manifold, otherwise it may cause sensor overheating and damage.
Only the qualified and trained fitter may carry out the security system installation.
The configured parameters of the security systems must comply with a vehicle manual instruction requirements.
StarLine data bus
DVR control output (2А) (+)
Starter output (200 mA) (–)
IGN1 output (200 mA) (–)
IGN2 output (200 mA) (–)
+12V output (500 mA) (+)
orange-black
white-green
brown-white
white-blue
brown
white
orange
gray-white
orange-white
white-black
red
orange
yellow
black-yellow
blue
green
After installation is complete, make sure to set current date
and time with pager (see manual at
help.starline.ru
).
The manufacturer StarLine ScPA LLC reserves the right to make technical
improvements not shown in this diagram.
Information on firmware updates, actual versions of operation and installation
manuals are available at
help.starline.ru
.
Check other available
connection options at
help.starline.ru
For convenient setup, diagnostics and software upgrade use the free StarLine Master
software available at
help.starline.ru/slm
Login into the program with a service code in the owner’s plastic card.
Set X2:6 blue wire as Starter protection and X2:15 orange wire as Engine
start: ACC in StarLine Master configuration program.
Ignition lock
Ignition lock
Starter
Ignition 1
Ignition 2
Power module V1
Power module V2
To connector Х2
To connector Х2
To the yellow
wire of
connector X1
To the yellow
wire of connector X1
Accessories
+12 V
+ 12 V
Security status output (200 мА) (–)
