background image

7 of 18 

® 

STANLEY    Electric Pressure Washers 

 

Rev: Dec2010 

Warnings 

Rapid retraction of starter cord (kickback) will pull hand and 
arm toward engine faster than you can let go. Broken bones, 
fractures, bruises or sprains could result. 



ALWAYS point gun in safe direction and squeeze spray gun trigger, to 
release pressure and avoid kickback each time, before starting engine. 
Engage trigger lock when not in use. 



When starting engine, pull cord slowly until resistance is felt and then 
pull rapidly to avoid kickback. 



After each starting attempt, where engine fails to run, always point gun in 
safe direction and squeeze spray gun trigger to release high pressure. 

WARNING 

WARNING 

Running engines produce heat. Temperature of muffler and nearby 
areas can reach or exceed 150°F (65°C). 

Severe burns can occur on contact. 

Exhaust heat/gases can ignite combustibles, structures or damage fuel 
tank causing a fire. 



DO NOT touch hot surfaces and avoid hot exhaust gases.  



Allow equipment to cool before touching. 



Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer 
including overhead. 



Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Prop-
erty require equipment powered by an internal combustion engine to have 
a spark arrester, maintained in effective working order, complying to 
USDA Forest service standard 5100-1C or later revision. In the State of 
California a spark arrester is required under section 4442 of the California 
Public resources code. Other states may have similar laws. 

The high pressure stream of water that this equipment produces can 
pierce skin and its underlying tissues, leading to serious injury and 
possible amputation. 

Spray gun traps high water pressure, even when engine is stopped 
and water is disconnected, which can cause injury. 

 



NEVER aim spray gun at people, animals or plants. 



DO NOT allow CHILDREN to operate pressure washer. 



NEVER repair high pressure hose. Replace it. 



NEVER repair leaking connections with sealant of any kind.  Replace o-
ring or seal. 



Keep high pressure hose connected to pump and spray gun while system 
is pressurized. 



ALWAYS point gun in safe direction and squeeze spray gun trigger, to 
release high pressure, every time you stop engine.  Engage trigger lock 
when not in use. 

WARNING 

Recoil starter and other rotating parts can entangle hands, hair, cloth-
ing, or accessories. 



DO NOT wear loose clothing, jewelry or anything that may be caught in 
the starter or other rotating parts. 



Tie up long hair and remove jewelry. 

High pressure spray can cause paint chips or other particles to be-
come airborne. 



Always wear eye protection when using this equipment or in vicinity of 
where equipment is in use. 

WARNING 

Unintentional sparking can result in fire or electric shock. 

 

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR 
PRESSURE WASHER 



Disconnect spark plug wire from spark plug and place wire  where it 
cannot contact spark plug. 

 
WHEN TESTING FOR ENGINE SPARK 



Use approved spark plug tester. 



DO NOT check for spark with spark plug removed. 

WARNING 

Excessively high or low operating speeds increase risk of injury and 
damage to pressure washer. 



DO NOT tamper with governed speed. 



DO NOT operate pressure washer above rated pressure. 

CAUTION 

WARNING 

Содержание P2350S




















Отзывы: