Stanley Bostitch T55 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 11

Stanley Bostitch T55 Series Скачать руководство пользователя страница 11

DIRECTIONAL EXHAUST DEFLECTOR

Loosen screw as shown. Adjust to desired exhaust direction and tighten screw.

-11-

ACCESSORIES AVAILABLE

BC601

4 oz. Stanley-Bostitch Air -Tool Lubricant

BC602

1 pint Stanley-Bostitch Air -Tool Lubricant

BC603

1 pint Stanley-Bostitch “Winter-Fromula” Air-Tool Lubricant

BC604

1 quart Stanley-Bostitch Air -Tool Lubricant

851325

Locite Grade 271 (.02 oz.)

851385

Locite Grade 242 (.02 oz.)

N80K2

Remote Control Kit

ORK1 O-Ring

Kit

BK6

Bumper Kit

T55K1

Speed Enhancer Kit

100679

Lube (1 lb can)

Models T55S4 and T55S5 contain a Quick Release Door feature. The door is designed to “pop” open if a jam occurs providing easy access for
removing a jammed fastener.

ALWAYS DISCONNECT AIR SUPPLY BEFORE CLEARING A JAMMED FASTENER.

If the door does not “pop” open when a jam occurs, it can easily be opened with a screwdriver, as shown in illustration #1. Use a firm twist on the
screwdriver to open the door, see illustration #2.
The door will not open completely if the driver is still down. To open the door completely the driver must be pushed back into the tool.
The “Quick Release Door” makes cleaning the nose and front portion of the magazine a rapid and easy operation with a minimum of effort.
To close the door simply press the door firmly against the edge of the work table or suitable stationary object until the two latch pins snap into a locked
position.
CAUTION:

Do not use your hands to close the door as injury may occur if skin is pinched between the door and nose when the latch pins
engage.

QUICK RELEASE DOOR

FIG. 1

FIG. 2

«
...
9
10
11

Содержание Bostitch T55 Series












Отзывы:

Нет отзывов