manualshive.com logo in svg

Stamina 15-7100, Руководство пользователя, Страница: 13 / 26

Поделиться
Скачать
Stamina 15-7100 Скачать руководство пользователя страница 13

13

SET UP INSTRUCTIONS

Place the 

Magnetic Fusion 7100 Bike

 in the area where it will be used. It is recommended that the 

Magnetic

Fusion 7100 Bike

 be placed on an equipment mat. The 

Magnetic Fusion 7100 Bike

 is approximately 53 1/4

inches long x 24 1/2 inches wide x 51 3/4 inches tall. (These dimensions may vary up to one inch.) An area
4 feet wide x 7 feet long is required for safe operation of the 

Magnetic Fusion 7100 Bike.

 Make sure that

adequate space is available for access to and passage around the 

Magnetic Fusion 7100 Bike.

To level the 

Magnetic Fusion 7100 Bike,

 first screw the 

STAND(60)

 located in the middle of

the 

FRONT FRAME(1)

 all the way up into the 

FRONT FRAME(1)

 so that it is not touching the

floor. 

Adjust the two 

LEVELING CAPS(57) 

on the 

REAR STABILIZER(6). 

When the 

LEVELING

CAPS(57)

 are adjusted and the 

Magnetic Fusion 7100 Bike

 

is stable, rotate the 

STAND(60)

to make it contact with the floor.
While you are adjusting the 

LEVELING CAPS(57) 

the 

STAND(60) 

must not be in contact with

the floor. Only after the 

Magnetic Fusion 7100 Bike 

has been stabilized with the 

LEVELING

CAPS(57)

 will you position the 

STAND(60) 

so it is in contact with the floor to provide extra

stability for the frame.
The 

Magnetic Fusion 7100 Bike

 has a 

WHEEL(54)

 on the 

FRONT STABILIZER (2).

 Lift up

the 

REAR STABILIZER(6)

 to move the 

Magnetic Fusion 7100 Bike.

LEVELING:

MOVING:

EQUIPMENT MAT 

(not included)

FUNCTION INSPECTION:

Visually inspect the 

Magnetic Fusion 7100 Bike

 to verify that assembly is as shown in the above illustration.

Check the function of the 

Magnetic Fusion 7100 Bike

 by turning the crank slowly through one complete

revolution to verify that the drive train functions properly. Use the 

UP

 and 

DOWN 

buttons on the 

COMPUTER

(26)

 to select a program and verify that the Magnetic System provides different tensions. Refer to the

COMPUTER INSTRUCTIONS

 on pages 15 to 17.

Locate and read the 

WARNING LABEL(95)

 on the 

Magnetic Fusion 7100 Bike.

 Make sure

that all users read the 

WARNING LABEL(95).

CAUTION:

Содержание 15-7100



























Отзывы:

Нет отзывов