ST X-NUCLEO-LED12A1 Скачать руководство пользователя

Страница: 8 / 17

Board setup

To test the expansion board follow the procedure below.

Step 1.

Connect the

X-NUCLEO-LED12A1

expansion board to the

STM32 Nucleo

development board from the

top through the Arduino UNO R3 connectors.

Step 2.

Power the

STM32 Nucleo

development board using a mini-B USB cable.

Step 3.

Program the firmware on the

STM32 Nucleo

development board using the provided example.

Step 4.

Reset the MCU using the

STM32 Nucleo

reset button.

Step 5.

Configure J15 jumper for internal or external LED power supply.
–

Connect pin 1 with pin 2 for external LED power supply.

–

Connect pin 2 with pin 3 for internal LED power supply.

For internal LED power supply, the PC USB port drives the LED current.

Important:
For external LED power supply, the current capability has to be provided through J13 connector. Do not apply an external
voltage greater than 6 V: as this is the absolute maximum rating of

LED1202

LED channels, it is recommended to remain

below 5.5 V.

UM2879

Board setup

UM2879

Rev 2

page 8/17

Содержание X-NUCLEO-LED12A1


















Результаты поиска

Содержание X-NUCLEO-LED12A1

Отзывы:

Похожие инструкции для X-NUCLEO-LED12A1

Бренды по названию

Популярные бренды

ST X-NUCLEO-LED12A1, Руководство пользователя

Результаты поиска

Содержание X-NUCLEO-LED12A1

Отзывы:

Похожие инструкции для X-NUCLEO-LED12A1

Бренды по названию

Популярные бренды