ST STM32F101xx series Скачать руководство пользователя страница 880 | Manualshive

Страница: 880 / 1096

ST STM32F101xx series Скачать руководство пользователя страница 880

USB on-the-go full-speed (OTG_FS)

RM0008

Doc ID 13902 Rev 12

OTG_FS device endpoint-x interrupt register (OTG_FS_DOEPINTx) (x = 0..3,
where x = Endpoint_number)

Address offset: 0xB08 + (Endpoint_number × 0x20)

Reset value: 0x0000 0080

This register indicates the status of an endpoint with respect to USB- and AHB-related
events. It is shown in

. The application must read this register when the OUT

Endpoints Interrupt bit of the OTG_FS_GINTSTS register (OEPINT bit in
OTG_FS_GINTSTS) is set. Before the application can read this register, it must first read
the OTG_FS_DAINT register to get the exact endpoint number for the OTG_FS_DOEPINTx

register. The application must clear the appropriate bit in this register to clear the
corresponding bits in the OTG_FS_DAINT and OTG_FS_GINTSTS registers.

Bit 0

XFRC:

Transfer completed interrupt

This field indicates that the programmed transfer is complete on the AHB as well as on the
USB, for this endpoint.

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Reserved

Re

s

e

rv

ed

B2BS

TU

P

Re

s

e

rv

ed

OT

E

P

D

IS

STUP

Re

s

e

rv

ed

EP

DISD

XFRC

rc_

w1
/rw

rc_

w1

rc_

w1

rc_

w1

rc_

w1

Bits 31:7 Reserved

Bit 6

B2BSTUP:

Back-to-back SETUP packets received

Applies to control OUT endpoint only.

This bit indicates that the core has received more than three back-to-back SETUP packets for
this particular endpoint.

Bit 5 Reserved

Bit 4

OTEPDIS:

OUT token received when endpoint disabled

Applies only to control OUT endpoints.

Indicates that an OUT token was received when the endpoint was not yet enabled. This
interrupt is asserted on the endpoint for which the OUT token was received.

Bit 3

STUP:

SETUP phase done

Applies to control OUT endpoint only.

Indicates that the SETUP phase for the control endpoint is complete and no more back-to-
back SETUP packets were received for the current control transfer. On this interrupt, the
application can decode the received SETUP data packet.

Bit 2 Reserved

Bit 1

EPDISD:

Endpoint disabled interrupt

This bit indicates that the endpoint is disabled per the application’s request.

Bit 0

XFRC:

Transfer completed interrupt

This field indicates that the programmed transfer is complete on the AHB as well as on the
USB, for this endpoint.

«
...
878
879
880
881
882
...
»

Содержание STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов