ST ST7LITEUS2 Скачать руководство пользователя страница 82

Страница: 82 / 136

Obsolete Product(s) - Obsolete Product(s)

On-chip peripherals

ST7LITEUS2, ST7LITEUS5

82/136

10.3.5 Interrupts

None.

10.3.6 Register

description

Control/Status register (ADCCSR)

Reset value: 0000 0000 (00h)

Note:

A write to the ADCCSR register (with ADON set) aborts the current conversion, resets the
EOC bit and starts a new conversion.

EOC

SPEED

ADON

CH2

CH1

CH0

Read/Write (Except bit 7 read only)

Bit 7

EOC

End of

Conversion

This bit is set by hardware. It is cleared by software reading the ADCDRH register.
0: Conversion is not complete
1: Conversion complete

Bit 6

SPEED

ADC clock selection

This bit is set and cleared by software. It is used together with the SLOW bit to
configure the ADC clock speed. Refer to the table in the SLOW bit description.

Bit 5

ADON

A/D Converter on

This bit is set and cleared by software.
0: A/D converter is switched off
1: A/D converter is switched on

Bits 4:3

Reserved.

Must be kept cleared.

Bits 2:0

CH[2:0]

Channel Selection

These bits are set and cleared by software. They select the analog input to convert.

Table 32.

Channel selection

Channel pin

CH2

CH1

CH0

AIN0

AIN1

AIN2

AIN3

AIN4

Obsolete Product(s) - Obsolete Product(s)

Содержание ST7LITEUS2









































































































































Результаты поиска

Содержание ST7LITEUS2

Отзывы:

ST ST7LITEUS2, Быстрый старт, Страница: 82 / 136

Результаты поиска

Содержание ST7LITEUS2

Отзывы: