SRAM RockShox Vivid Air R2 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 27

SRAM RockShox Vivid Air R2 Скачать руководство пользователя страница 12

GEN.0000000003161 REV A

12

SERviCE inSTRuCTionS (ConTinuEd)

AiR CAn SERviCE (RouTinE SERviCE)

When using a pick to remove seals, be careful

not to damage the shock parts. Any damage will

allow air/oil to bypass the seals, resulting in

decreased performance.

After the removal of each seal/glide ring, spray

isopropyl alcohol into the glands and wipe them

with a clean lint free rag. Apply a small amount

of grease to the new glide rings/seals before

installing them.

Remove the top out bumper and air seal head by

17.

pulling them up and off of the shock body.

Remove and replace the shaft eyelet/air can

18.

o-ring, located at the base of the threads on the

shaft eyelet.

(CoMpREhEnSivE SERviCE)

19.

Use isopropyl alcohol to clean the inner surface

of the air can inner sleeve. Remove the inner

sleeve from the air can by wedging the index

and middle fingers of each of your hands into the

inside of the inner sleeve, then pushing against

the air can with your thumbs.

Make sure your fingers are clean and dry to

achieve the best grip on the inner sleeve.

(CoMpREhEnSivE SERviCE)

20.

Remove and replace the inner sleeve o-ring.

(CoMpREhEnSivE SERviCE)

21.

if the plastic centering ring came dislodged

from the air can during inner sleeve removal, re-

install it into the air can with the stepped side

oriented toward the inside of the air can.

Install the inner sleeve, non-o-ring side first,

into the air can. Locate the inner sleeve around

the plastic centering ring. Press the inner

sleeve into the can until it stops, then check the

alignment of the sleeve in the can. The plastic

centering ring should be completely visible

inside the inner sleeve. If not, use your thumbs

and fingers to center the sleeve in the can, then

firmly press the sleeve into the can until it is

completely seated.

To prevent damage to the air can, center the

inner sleeve around the plastic centering ring

in the air can before pressing firmly on the inner

sleeve or assembling the air can and air can

seal head.

17

18

19

20

plastic centering ring

21

«
...
10
11
12
13
14
...
»

Содержание RockShox Vivid Air R2




























Отзывы:

Нет отзывов