manualshive.com logo in svg

SRAM Rock Shox Lyrik RC, Руководство по обслуживанию

Поделиться
Скачать
SRAM Rock Shox Lyrik RC Скачать руководство пользователя страница 29

29

Charger Rebound Damper Re-tune (optional)

C h a r g e r   R e b o u n d   D a m p e r   R e - t u n e   ( o p t i o n a l )

All Lyrik Charger rebound dampers are configured in a medium damper tune. The rebound piston shims can however be re-arranged for a soft or  

firm tune.
If your rebound setting is one or two clicks from open, we recommend changing to a soft rebound tune.
If your rebound setting is one or two clicks from closed, we recommend changing to a firm rebound tune. 

Clamp the bottom of the rebound damper shaft into a RockShox Rear 

Shock Vise Block. 

NOTICE

To prevent damage to the rebound damper shaft, do not clamp the 

middle of the shaft in the vise.

Use a 10 mm socket to remove the piston nut. Use your hand to 

stabilize the rebound damper shaft.

Use a small wrench or pick to slide the shims off of the rebound 

damper piston. Set the shims on a rag in the order they came off of  

the piston.

1 

2 

10 mm 

3 

Small wrench or pick

Содержание Rock Shox Lyrik RC
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды