SRAM G2 RSC Скачать руководство пользователя страница 36

Страница: 36 / 42

Brake Hose Installation

B r a k e H o s e I n s t a l l a t i o n

Cut the hose to install a new barb and compression fitting.

⚠

WARNING

All SRAM brakes that use a compression fitting and hose barb

must use a new SJ (Stealth-a-majig) hose barb and a new, red SJ

compression fitting upon reassembly.
The factory may have installed a non-red SJ compression fitting,

which functioned properly prior to disconnection. Upon reconnection,

you must install a new SJ hose barb and a new, red SJ compression

fitting.
Brake hoses assembled with non-Stealth-a-majig hose barbs and

compression fittings, will not function.

Apply DOT grease to the hose barb threads. Thread the hose barb into

the hose until it is flush with the end of the hose.

NOTICE

Do not overtighten the hose barb. Overtightening may cause damage

to the hose liner.

Install the compression nut onto the hose.

Thread the compression fitting over the hose barb, counter-clockwise,

until it is flush or slightly lower than the hose barb.

The compression fitting is reverse threaded.

Apply DOT grease to the outside of the compression fitting and the

threads of the compression nut.

SRAM Hydraulic Hose Cutter

DOT Grease

Содержание G2 RSC











































Результаты поиска

Содержание G2 RSC

Отзывы:

Похожие инструкции для G2 RSC

Бренды по названию

Популярные бренды

SRAM G2 RSC, Руководство по обслуживанию

Результаты поиска

Содержание G2 RSC

Отзывы:

Похожие инструкции для G2 RSC

Бренды по названию

Популярные бренды