SPXFLOW Seital Separation SE 40CX-Q2P2 страница 67 Скачать руководство пользователя

Страница: 67 / 126

Chapter 9
Rev. 1 of 14/01/97

SEITAL S.r.l.

Use and maintenance handbook: Centrifugal separator

SE 40CX

Page 9-3

9.4. Horizontal shaft assembly (Tab. 07)

Before assembly clean and check all parts carefully, with particular attention to gaskets and
ball bearings.
When assembling the horizontal shaft, place the two supports (07.150.0) and (07.300.0) are at
the bottom side.

Assemble ball bearing and support - brake side (07.270.0



07.310.0). Insert the whole

thus assembled into the frame and onto the horizontal shaft. Fix the support (07.300.0) to
the frame by the screws (07.330.0).

Insert ball bearing (07.180.0) on horizontal shaft (07.200.0).

Insert horizontal shaft and ball bearing at the same time on frame and in helical wheel
unit (parts 07.220.0 to 07.260.0)

Verify that the space between the support (07.150.0) and ball bearing (07.180.0) is at
least 2 mm.

Fix support (07.150.0) on frame with OR gasket (07.160.0) and spring (07.170.0) by
screwing the screws (07.130.0).

Slide helical gear wheel in correct position and fix it on horizontal shaft fastening hardly
the screws (07.260.0).

Check the pickup is in correct position (1 mm. from phonic wheel of brake disk).

Insert on the shaft the brake disk (07.390.0) and fix it with the screw (07.410.0), after
having placed the washer (07.400.0).

Preassemble the brake unit (07.420.0



07.460.0) and fix it to the frame by the screws

(07.480.0).

10) Insert on the shaft the fluid coupling with flexible coupling (07.070.0



07.110.0).

11) Fix the motor adapter flange (07.040.0) to the frame by the screws (07.050.0). Insert the

motor (07.030.0) fixing by the screws (07.010.0).

12) Remount the gear chamber flange, air grating of hydraulic coupling and motor cover

(Tab.08).

13) Fill gear chamber with recommended oil (see § 5.5.1).

Содержание Seital Separation SE 40CX-Q2P2































































































































Результаты поиска

Содержание Seital Separation SE 40CX-Q2P2

Отзывы:

Похожие инструкции для Seital Separation SE 40CX-Q2P2

Бренды по названию

Популярные бренды

SPXFLOW Seital Separation SE 40CX-Q2P2, Инструкция по эксплуатации

Результаты поиска

Содержание Seital Separation SE 40CX-Q2P2

Отзывы:

Похожие инструкции для Seital Separation SE 40CX-Q2P2

Бренды по названию

Популярные бренды